Jenn-Air JMW8527DA Series Service Manual page 44

Installation Instructions
fkpq^ii^qflk
fkpqor`qflkp
PM² t^ii lsbk abp`ofmqflk
1 1-1/4² Dia. Conduit Access Hole*
2 5/8² Plywood Floor (Must Support 250 lbs.)
afjbkpflkp
†‹
A 30 MIN
B 24 MIN
C 47 + 1/16
D 24 MIN
E 28-1/2 + 1/16
F 47-5/8
G 29-3/4
H 24-7/16
I 4 to 20
* Hole must be cut as close to corner of cabinet as possible.
klqbp
Z Do not block air intake slots along bottom of oven.
fkpq^ii^qflk
1. Cut hole in cabinet to mount oven. Cutout in
cabinet should be level and straight.
klqbW There are no provisions to level the unit
after it is installed. An oven that is not level could
cause poor baking results.
2. Install plywood floor as shown above.
3. Attach unit to the cabinet with 4 No. 8² flat head
screws supplied inside of envelope containing
these instructions. Pre-drill holes in cabinet for
attachment screws using 1/8² drill. Oven
mounting holes are provided in side trim.
4. See instructions "Electrical Connections" for
electrical hook-up.
5. See figure 1 for lower trim installation.
6. See User's Manual for operating instructions.
cŒ b’Œ‚~‹ ‘–‰‚ €~†‹‚‘ Eƒ‰’… ƒŒ‹‘F ‘…‚ ‚Ž’†‚ €‰‚~~‹€‚ ƒŒ Œ‚~‘†Œ‹ Œƒ ‘…‚ Œ“‚‹ ŒŒ † Š†‹†Š’Š
~€†‹„ Œƒ TLU² ‚‘”‚‚‹ ‘…‚ €’‘Œ’‘ ~‹ ‘…‚ ŒŒI …†‹„‚ Œ ~”‚ Œƒ ‘…‚ €~†‹‚‘K
pŒŠ‚ ’†‰‘J†‹ €~†‹‚‘ Š~– ‹Œ‘ ‚ ”†‚ ‚‹Œ’„…I ’‚ ‘Œ ‘…‚† €Œ‹‘’€‘†Œ‹I ‘Œ ~‰‰Œ” ‘…† †‹‘~‰‰~‘†Œ‹K
A – 6
_’†‰‘Jf‹ PM² ² ² ² b‰‚€‘†€
`ŒŠ†‹~‘†Œ‹ t~‰‰ l“‚‹
€Š
76.20 MIN
60.96 MIN
119.38 + .16
60.96
72.39 + .16
120.97
75.57
62.07
10.2 to 50.8
`^rqflk
16022821 Rev. 0
403 WEST FOURTH STREET, NORTH
`lj_fk^qflk t^iilsbk `rqlrq
cfdrob N
Remove lower screws from hinge receptacle plates. Align
lower trim and reinstall screws.
klqbW Lower trim overlaps front edge of cabinet by 9/16².
NEWTON, IA 50208
UNMNmRSRJSM
(07-03-00)
©2004 Maytag Appliances Company