The B Memory Section; Programming, Recalling And Altering Memories (Scenes); Programming; Fading In Scenes - Behringer Eurolight LC2412 User Manual

EUROLIGHT LC2412
2. Now, set up the lighting situation by using the faders of the
B MEMORY section. As always, you can observe these
changes on the control LEDs.
3. Move the master B fader downward, then move the master
A fader upward. Preset B is faded out, while preset A is
faded in (manual fade).

4. THE B MEMORY SECTION

In this context, “memory” means a lighting situation (preset)
stored as a unit.
The memory function is organized as follows:
There are ten storage banks, each with twelve storage slots
(FLASH keys 1 - 12), used to store complete lighting situations
(24 channels). The illumination level of the individual lighting
situations (stage designs) can be determined by using the faders
assigned to them during the programming procedure.
You can use memories in several ways:
1. Fade them in manually or suddenly;
2. Crossfade between presets and memories;
3. Crossfade between different memories;
4. Crossfade between memories from different memory banks.
Memories originating in different banks can simultaneously
be active.
4.1 Programming, recalling and altering
memories (scenes)

4.1.1 Programming

1. Set up a stage design (scene) while in preset mode (Fader A
PRESET section).
2. To store a scene, you must first quit the preset mode. By
using the UP/DOWN keys
mode. The bank display
selected.
Press the MEMORY key in the programming section. The
display shows the following text (an example):
Fig. 4.1: Display “Program memory”
The meaning behind the above line: the next step (select
memory), location (memory slot number/storage bank).
You have already selected a storage bank using the UP/DOWN
keys (7), and now use the FLASH keys to select a location.
Lower line: Make a selection by pressing SOFT A (preset) or
SOFT B (all).
If you only want to store the adjusted preset, please press
SOFT A . If you also want to store an active memory along
with the adjusted preset, then press SOFT B
+
Should you wish to store additional presets, simply repeat the
steps:
1. Adjust the preset (stage design);
2. Select a storage bank using the UP/DOWN keys;
12
, you switch into the memory
indicates which storage bank is
.
4. THE B MEMORY SECTION
3. Specify the storage location by pressing one of the FLASH
keys / ;
4. Store the preset or the console output (SOFT A or B);
5. If you do not wish to create any more memories, press the
QUIT key to exit.

4.1.2 Fading in scenes

To fade in a programmed scene, simply select a storage bank
by using the UP/DOWN keys and pull up a fader from the B
MEMORY section. The fader whose assigned FLASH key you
last pressed while programming is the fader that will control this
memory.
+
By using the FLASH keys (section
memories from the bank you just adjusted, just like retrieving
individual channels in preset mode (“P” shown in the display).
+

4.1.3 Previewing and modifying memories

To preview memories before fading them in, use the PREVIEW
key to deactivate the console output for this procedure. The
setup can only be observed on the control LEDs. The remaining
functions of the EUROLIGHT LC2412 remain active.
After you press the preview key, the display shows the
selected memory bank at the top right side. Select the memory
that you wish to control by using one of the FLASH keys. The
memory is then displayed by means of control lights only.
If you wish to modify the memory shown in preview mode,
select the MODIFY function shown in the display by using the
SOFT B key (see fig. 4.2).
Fig. 4.2: Display “Editing memory in preview mode”
You can implement the desired changes now by using the
faders of the A PRESET section. To change the programmed
settings of preset faders, you must first draw the fader to its
original position. The channels not activated during the previous
programming can be raised as usual.
To save your settings, please select ENTER by using SOFT B.
Either confirm the next memory or quit the preview mode by
hitting the QUIT key .
Otherwise, you can also program the memory anew, as
described at the beginning of this chapter.

4.2 Crossfading between different setups

4.2.1 Crossfading between presets and memories

Crossfading between memories and presets works exactly
the same way as crossfading between two presets. The only
difference is that the EUROLIGHT LC2412 has to be in memory
mode.
1. Activate a stored scene (see chapter 4.1.2).
2. Activate a preset by using a fader from the A PRESET section;
fader A remains locked.
), you can recall the