AMX NX-1200 Hardware Reference Manual page 16

NX-2200 Specifications (Cont.)
USB Port:
Master LEDs:
ICSLAN LEDs (red):
Serial LEDs (red):
Relay (red):
IR/Serial (red):
Digital I/O (yellow):
Rear Panel Components:
RS-232/422/485
(Port 1):
RS-232 (Ports 2-4):
Relay (Port 21):
Digital I/O (Port 22):
IR/Serial
(Ports 11-14):
AxLink Port:
Configuration DIP
Switch:
ICSLAN:
USB Port:
ID Pushbutton:
Hardware Reference Guide - NX-Series NetLinx Integrated Controllers
1 Type-A USB port for connecting a mass storage device for loading .tkn files, reading
or writing configuration files and log files, or updating the firmware on the unit.
• LINK/ACT (green): Blinks when the Ethernet cables are connected and terminated
correctly. Also blinks when receiving Ethernet data packets.
• STATUS (green): Blinks to indicate that the system is programmed and
communicating properly.
• OUTPUT (red): Blinks when the Controller transmits data, sets channels On and Off,
sends data strings, etc.
• INPUT (yellow): Blinks when the Controller receives data from button pushes, strings,
commands, channel levels, etc.
1 LED which blinks when the RJ-45 cables to port 1 is connected and terminated
correctly. The LED also blinks when receiving LAN data packets.
2 sets of four LEDs, each of which light to indicate that the corresponding RS-232 ports
(2-4) and RS-232/422/485 port (1) are transmitting or receiving RS-232, 422, or 485
data.
4 LEDs light to indicate the relay channels 1-4 are active (closed). These LEDs reflect
the state of the relay on port 21.
4 LEDs light to indicate the IR/Serial ports 11-14 are transmitting control data. LED
indicator for each IR port remains lit for the length of time that IR/Serial data is being
generated.
Lights when the I/O channels 1-4 are active. The LED for each I/O port reflects the state
of that particular port.
1 10-pin RS-232/422/485 control ports using a 10-pin 3.5 mm mini-Phoenix (male)
connector with XON/XOFF (transmit on/transmit off), CTS/RTS (clear to send/ready to
send). Supports 300-115,200 baud.
3 5-pin RS-232 control ports using 5-pin 3.5 mm mini-Phoenix (male) connectors with
XON/XOFF (transmit on/transmit off), CTS/RTS (clear to send/ready to send). Supports
300-115,200 baud.
4 2-pin 4-channel single-pole single-throw relay ports.
Each relay is independently controlled.
Supports up to 4 independent external relay devices
Channel range = 1-4
Each relay can switch up to 24 V
8-pin 3.5 mm mini-Phoenix (male) connector provides connection to relays
4-channel binary I/O port for contact closure with each input being capable of voltage
sensing. Input format is software selectable with interactive power sensing for IR ports.
4 IR/Serial control ports support high-frequency carriers of up to 1.142 MHz with each
output being capable of two electrical formats: IR or Serial.
4 IR/Serial data signals can be generated simultaneously.
IR ports support data mode (at limited baud rates and wiring distances).
4-pin 3.5 mm mini-Phoenix (male) connector that provides data and power to external
AxLink control devices. Green AxLink LED indicates the state of the AxLink port.
The Configuration DIP Switch allows you to set boot-time operations (see Configuration
DIP Switch section on page 30 for more information.)
1 RJ-45 connector for ICSLAN interface.
1 Type-A USB port for connecting a mass storage device for loading .tkn files, reading
or writing configuration files and log files, or updating the firmware on the unit.
1 black ID pushbutton used during boot to revert to factory configuration or factory
firmware. Also used after boot to toggle IP mode between Static and DHCP.
or 28 V @ 1 A
DC AC
Overview
9