Specifications - Technics SA-DA20 Operating Instructions Manual

Specifications

AMPLIFIER SECTION
Power output (at 230 V for Continental Europe)
(at 240 V for the United Kingdom)
DIN 1 kHz (T.H.D. 1 %)
20 Hz–20 kHz continuous power output
both channels driven
Total harmonic distortion
rated power at 20 Hz–20 kHz
half power at 1 kHz
DVD 6CH power output
DIN 1 kHz (T.H.D. 1 %)
Front
Center
Surround
Power bandwidth
both channels driven, –3 dB
Damping factor
Load impedance
Front
A or B
A and B
BI-WIRE
Center
Surround
Frequency response
PHONO RIAA standard curve (30 Hz–15 kHz) ±0.8 dB
CD, TAPE/MD, DVD, TV, VCR 1, VCR 2, VCR 3
Input sensitivity and impedance
PHONO
CD, TAPE/MD, DVD, TV, VCR 1, VCR 2, VCR 3 200 mV/22 kΩ
S/N at rated power (6 Ω) (VGCA ON)
PHONO
CD, TAPE/MD, DVD (L/R/C/LS/RS), TV, VCR 1, VCR 2, VCR 3
113 dB (IHF, A rated power, S=2 V), 98 dB (IHF, A: 100 dB)
Tone controls
BASS
TREBLE
Output voltage
TAPE/MD REC (OUT), VCR 1 OUT
Channel balance (250 Hz–6.3 kHz)
Channel separation
Headphones output level and impedance
Subwoofer frequency response (–6 dB)
Digital input
Optical
Coaxial
(DIN 45 500)
2 x 100 W (6 Ω)
2 x 80 W (6 Ω)
0.05 % (6 Ω)
0.03 % (6 Ω)
2 x 100 W (6 Ω)
100 W (6 Ω)
2 x 100 W (6 Ω)
10 Hz–100 kHz (6 Ω, 0.9 %)
30 (6 Ω)
4–16 Ω
8–16 Ω
6–16 Ω
6–16 Ω
6–16 Ω
10 Hz–100 kHz, ±3 dB
3 mV/47 kΩ
70 dB (IHF, A: 80 dB)
50 Hz, +10 to –10 dB
20 kHz, +10 to –10 dB
200 mV
±1 dB
55 dB
430 mV/330 Ω
7–200 Hz
2
1
FM TUNER SECTION
Frequency range
Sensitivity
S/N 30 dB
S/N 26 dB
S/N 20 dB
IHF usable sensitivity (IHF'58)
IHF 46 dB stereo quieting sensitivity
Total harmonic distortion
MONO
STEREO
S/N
MONO
STEREO
Frequency response
20 Hz–15 kHz
Alternate channel selectivity
±400 kHz
Capture ratio
Image rejection at 98 MHz
IF rejection at 98 MHz
Spurious response rejection at 98 MHz
AM suppression
Stereo separation
1 kHz
Carrier leak
19 kHz
38 kHz
Channel balance (250 Hz–6.3 kHz)
Limiting point
Bandwidth
IF amplifier
FM demodulator
Antenna terminal
AM TUNER SECTION
Frequency range
Sensitivity
Selectivity (at 999 kHz)
IF rejection (at 999 kHz)
VIDEO SECTION
Output voltage at 1 V input (unbalanced)
Maximum input voltage
Input/output impedance
GENERAL
Power supply
For Continental Europe
For the United Kingdom
Power consumption
Dimensions (W x H x D)
Mass
Power consumption in standby mode:
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
87.50–108.00 MHz
1.5 µV/75 Ω
1.3 µV/75 Ω
1.2 µV/75 Ω
1.5 µV/75 Ω
22 µV/75 Ω
0.2 %
0.3 %
60 dB (75 dB, IHF)
58 dB (71 dB, IHF)
+1 dB, –2 dB
65 dB
1.5 dB
40 dB
70 dB
70 dB
50 dB
40 dB
–30 dB (–35 dB, IHF)
–50 dB (–55 dB, IHF)
±1.5 dB
1.2 µV
180 kHz
1000 kHz
75 Ω (unbalanced)
522–1611 kHz (9 kHz steps)
530–1620 kHz (10 kHz steps)
20 µV, 330 µV/m
55 dB
50 dB
1±0.1 Vp-p
1.5 Vp-p
75 Ω (unbalanced)
AC 230 V, 50 Hz
AC 230–240 V, 50 Hz
270 W
[SA-DA20] 430 x 180 x 370 mm
[SA-DA15] 430 x 158 x 370 mm
[SA-DA20] 13.7 kg
[SA-DA15] 11.7 kg
2 W
39
RQT5861