Monessen Hearth ICFDV30LNTSC Installation And Operating Instructions Manual page 31

TOuCh SCReeN ReMOTe CONTROL OpeRATION
1. Press the ON/up button to turn
on the fireplace. The flame icon
on the LCD displays High.
2. Press the OFF/down button to
decrease the flame height and
turn off the fireplace. When the
OFF/down button is pressed
for three times, the flame icon
changes form High to Medium,
to Low, then to Off.
3. If the OFF button is held for
more than 3 seconds at any
flame height, the fireplace will
be turned off and the flame icon
disappears.
4. Sliding up and down on the arrow buttons can also
turn on or turn off the fireplace.
5. If the fireplace is shut off using the above methods in 3
and 4, all the settings will be remembered and will be
resumed next time the fireplace is turned on (Memory
Off).
Timer Mode
Figure 35
Press the TIMER button to enter
timer mode. The fireplace will stay
on for a period of time as specified
by the timer and then be shut off
by the transmitter when the timer
counts down to zero.
1. When the TIMER button is
pressed, the Set Time appears
in the frame of the button and
flashes.
2. Use ON/up and OFF/down to
increase or decrease the Set Time in 15 min. incre-
ments, between 0:00 to 6:00. Sliding up and down on
the arrow buttons will increase or decrease the Set
Time in 1 hour increments.
3. Push the TIMER button again to confirm the Set Time,
the transmitter sends an ON signal to turn on the fire-
place.
4. The flashing stops and the ON/up and OFF/down but-
tons become flame height controller again. The flame
height will then stay as set up by the ON/up and OFF/
down buttons.
5. The TIMER button can be used when the transmit-
ter is in Manual Mode or in Thermostat Mode. In both
modes, the fireplace will be shut down completely
when the timer counts down to zero.
6. To exit Timer Mode,
a. Push and hold the TIMER button for 3 seconds Or
b. Use the OFF/down buttons to decrease the Set
Time to zero Or
20304164
Thermostat Mode
Figure 36
NOTe: The Command Center but-
tons will disable when thermostat is
being used.
Press the THERMO button to set
the transmitter in thermostat mode.
The transmitter will automatically
turn on the fireplace when the
room temperature is below the set
temperature and turn off the appli-
ance when the room temperature
Figure 34
is above the set temperature within
FP2651
one degree.
Manual mode
1. When the THERMO button is pressed, the Set temper-
2. Use ON/up and OFF/down to increase or decrease
3. Press the THERMO button again to confirm the Set
4. The flashing stops and the ON/up and OFF/down but-
5. To exit Thermostat Mode:
Figure 35
FP2652
Timer mode
Smart Mode
Mode
Figure 37
Press and hold the THER-
MO button and the ON/UP
button at the same time
for 3 seconds to toggle
between
thermostat and the regu-
lar Thermostat Mode. The
icon "Smart Mode" will ap-
pear under the Set Tem-
perature. The transmitter
will automatically adjust
the flame height according
to the difference between
c. Slide down on the arrow buttons to exit TIMER
mode and shut off the fireplace.
ature appears in the frame of the button and flashes.
the Set temperature in 1 degree increments, between
45 degrees and 90 degrees. Slide up and down on the
arrow buttons will increase or decrease the Set Tem-
perature in 10 degrees increments.
Temperature. The transmitter will send out an On
signal or an Off signal depending on the relationship
between the Set temperature and the Room tempera-
ture.
tons become flame height controller again. The flame
height will then stay as set up by the ON/up and OFF/
down buttons.
a. push and hold the THERMO buttons for 3 sec-
onds or
b. slide down on the arrow buttons to exit Thermo-
stat mode and shut off the fireplace.
®
Thermostat Option for Thermostat
®
Smart Mode
ICFDV Fireplace Insert
Figure 36
FP2653
thermo mode
Smart
Mode
Icon
Figure 37
FP2654
smart mode
31