Nokia E7-00 Service Manual

Hide thumbs Also See for E7-00:

User manual (141 pages)

User manual (128 pages)

User manual (140 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Nokia E7-00

Page 1 Up to 9 hours Up to 430 hours WCDMA: WCDMA: Up to 5 hours Up to 470 hours Note: Talk times are dependent on network parameters and phone settings Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 2: Table Of Contents
BATTERY INFORMATION ..............................8 EXPLODED VIEW ................................. 9 SERVICE DEVICES ................................11 SOFTWARE UPDATE ................................12 DISASSEMBLY INSTRUCTIONS ............................13 10. ASSEMBLY INSTRUCTIONS ............................... 25 11. SOLDER COMPONENTS ..............................38 Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 3 18.11.2010 First approved version The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to carry out service to NOKIA products. This Service Manual is to be used only by authorized NOKIA service suppliers, and the content of it is confidential. Please note that NOKIA provides also other guidance documents (e.g.
Page 4: Copyright
Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
Page 5: Warnings And Cautions
3. Use only approved components as specified in the parts list. 4. Ensure all components, modules screws and insulators are correctly re–fitted after servicing and alignment. 5. Ensure all cables and wires are repositioned correctly Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 6: Esd Protection
RM-626 Service Manual Level 1&2 3. ESD PROTECTION Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use.
Page 8: Battery Information
Batteries’ performance is particularly limited in temperatures well below freezing. Do not dispose batteries in a fire! Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 9: Exploded View
I0001 SCREW TORX+ SIZE 4 TOP END CAP RF1.4x3.0 I0003 I0002 Only available Not reuseable Repair/swap Ver. 1.0 Page 1/2 as assembly after removal only in level 3 Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 10 SIM HOLDER I0235 BACK COVER I0233 SCREW TORX+ SIZE 4 M1.4x3.9 I0234 Only available Not reuseable Repair/swap Ver. 1.0 Page 2/2 as assembly after removal only in level 3 Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 11: Service Devices
Online. Supplier or manufacturer contacts for tool re-order can be found in “Recommended service BL-4D Battery SS-210 Camera Removal tool equipment” document on Nokia Online. SS-231 RF Connector tool Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 12: Software Update
To use the FLS-5 Flash Dongle, follow the user guide inside the sales package. Please check always for the latest version of flash software, which is available on Nokia Online. Confidential | Copyright © 2010 Nokia | All rights reserved...
Page 13: Disassembly Instructions
4) Pull out the SIM HOLDER with the SRT-6 and remove it. 5) Open the HDMI door. 6) Use the SRT-6 to release the TOP END DECO as shown. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 14 10) Remove the TOP END CAP. direction shown. 11) To release the BOTTOM END DECO, slide the SRT-6 12) Remove the BOTTOM END DECO. under it to the direction shown. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 15 17) Then turn the display part of the device as 18) Unscrew the four Phillips size 00 screws in the shown. order shown. Do not use them again. Discard them. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 16 CONNECTOR LOCK PLATE carefully with the dental tool. Be careful not to injure yourself or the connector under the CONNECTOR LOCK PLATE with the sharp end of the dental tool! Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 17 29) Use the dental tool to lever out the IHF SPEAKER. 30) Unscrew the two Torx+ size 4 screws in the order Remove the IHF SPEAKER with the tweezers. shown. Do not use them again. Discard them. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 18 35) Use the same procedure on the second cable 36) Turn the ENGINE BOARD carefully around. Open connector. the UI FLEX connector with the SRT-6. Be careful not to damage the connector or nearby components! Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 19 Discard it. 41) Remove also the WASHER with the tweezers. 42) Use the SS-231 to release the other end of the BLACK COAX CABLE. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 20 Torx+ size 4 screws in the order shown. Do not side as shown and unscrew the four Torx+ size 4 use them again. Discard them. screws in the order shown. Do not use them again. Discard them. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 21 Be careful not to damage the WINDOW, be careful not to damage the WINDOW WINDOW flex! Note that only the WINDOW has to be flex. lifted. The DISPLAY should remain on its place. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 22 59) Protect the other side of the WINDOW with 60) Use the SRT-6 to release the SPACER FLEX LID. Be protective film. careful not to damage the components nearby! Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 23 Be very careful not to damage the flex while releasing it. 65) Release the EARPIECE with the SRT-6. 66) Remove the EARPIECE with the tweezers. Do not use the EARPIECE again. Discard it. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 25: Assembly Instructions
5) Slide the SS-231 to direction shown to lock it to 6) Push the connector to its place with the SS-231. the BLACK COAX CABLE connector. Make sure BLACK COAX CABLE is connected to the shown connector. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 26 11) Tighten the Phillips size 00 screw to the torque 12) Push the CABLE COVER to its place. Make sure that of 10 Ncm. cables are inside the CABLE COVER. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 27 17) Attach the WINDOW flex adhesive by gently 18) Remove the SPACER FLEX LID adhesive protective pressing with the SS-93. Be careful not to damage film. the connector or any nearby components. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 28 22) Press the DISPLAY flex to bend it as shown. damage the DISPLAY flex while turning the DISPLAY. 23) Remove the DISPLAY protective film. 24) Remove the protective film from the inner side of the WINDOW. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 29 30) Tighten these two TORX + size 4 screws to the size 4 screws to the torque of 5 Ncm in the order torque of 12 Ncm in the order shown. shown. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 30 35) Remove the DUMMY KEYMAT with the tweezers 36) Move the two coaxial cables to the side, so that and close the device. they are not damaged while assembling the ENGINE BOARD. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 31 42) Place the ENGINE BOARD FRAME ASSEMBLY onto connector to the connector marked with a letter W. the ENGINE BOARD. Press from the shown places to lock it to its place. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 32 47) Press gently the CAMERA MODULE with the SS-93 48) Open up the device. Connect the QWERTY to attach the camera retaining clips. connector with the SS-93. Be careful not to damage the connector. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 33 53) Then press from the opposite side to lock the 54) Tighten the four TORX + size 4 screws to the BACK COVER to the BASE CHASSIS ASSEMBLY. torque of 14 Ncm in the order shown. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 34 59) Take new BOTTOM END DECO. 60) Attach the BOTTOM END DECO onto the BOTTOM END CAP as shown. Press the BOTTOM END DECO to activate the adhesive. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 36 END DECO to lock it into its place. 71) Push in the SIM HOLDER. 72) Test that the volume key is working by pushing it in both directions few times. Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 37 74) Remove the lock key protective film. 75) Test that the lock key is working by pushing it 76) Now the Nokia E7-00 assembly procedure is few times. complete. -END OF ASSEMBLY- Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...
Page 38: Solder Components
RM-626 Service Manual Level 1&2 11. SOLDER COMPONENTS S2402 X2701 X2702 X2400 X1650 V2505 V2506 F3300 BOTTOM X6705 X1502 X6700 X1500 V1500 X6704 X6703 X7403 X7402 Ver. 1.0 Confidential | Copyright © 2010 Nokia | All rights reserved Version 1.0...

This manual is also suitable for:

Rm-626

Nokia E7-00 Service Manual

Quick Links

Related Manuals for Nokia E7-00

Summary of Contents for Nokia E7-00

This manual is also suitable for:

Table of Contents