Electrolux MCC4060E Service Manual page 34

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
REMOVAL
1. Disconnect the oven from the power supply.
2. Remove the turntable and roller stay from the
oven cavity.
3. Turn the oven over.
4. Cut the three (3) bridges holding the turntable
motor cover to the base plate with cutting pliers as
shown in Figure C-1(a).
CAUTION: DO NOT DROP THE TURNTABLE
MOTOR COVER INTO THE OVEN AFTER
CUTTING THE BRIDGES. BECAUSE IT
WILL DAMAGE THE WIRE LEADS OF
THE MOTOR AND IT IS DIFFICULT TO
REMOVE IT OUT OF THE OVEN.
5. Remove the turntable motor cover from the base
plate.
6. Disconnect the wire leads from the turntable motor.
Bridges
Figure C-1(a). Turntable motor cover removal
CONVECTION MOTOR AND CONVECTION HEATING ELEMENT REMOVAL
1. CARRY OUT 3D CHECKS.
Now,the outer case cabinet and the air duct should
have been removed.
2. Remove the one (1) screw holding the earth wire of
the power supply cord to the back plate.
3. Release the power supply cord from the back plate.
4. Remove the two (2) screws holding the rear barrier
to the base plate.
5. Release the three (3) tabs of rear barrier from the
base plate. And remove the rear barrier.
6. Remove the one (1) screw holding the back plate to
the base plate.
7. Remove the one (1) screw holding the chassis
support to the back plate.
8. Remove the one (1) screw holding the the back plate
to the air intake duct.
9. Remove the two (2) screws holding the back plate to
the convection duct.
10. Remove the back plate from the oven cavity.
11. Disconnect the wire leads from the convection
heating elements, convection motor and thermal cut-
out.
12. Remove the one (1) screw holding the convection
duct to the oven cavity back plate from outside of the
oven cavity.
SOI 12.06 FV
TURNTABLE MOTOR REPLACEMENT
Cutting pliers
Base plate
Turntable motor
cover
34/43
7. Remove the two (2) screws holding the turntable
motor to the oven cavity back plate.
8. Remove the turntable motor from the turntable
motor angle. Now, the turntable motor is free.
RE-INSTALL
1. Remove the any sharp edges on the turntable
motor cover and the base plate with the cutting
pliers.
2. Re-install turntable motor by locating shaft onto
coupling to the oven cavity base plate with the two
(2) screws.
3. Re-connect the wire leads to the turntable motor.
4. Insert the one (1) tab of the turntable motor cover
into the slit of the base plate as shown in Figure
C-1(b).
5. Re-install the turntable motor cover to the base plate
with the screw (code 5028 63 98-00/8) as
shown in Figure C-1(b).
Turntable
motor cover
Tab
Slit
Figure C-1(b). Turntable motor cover re-install
13. Remove the seven (7) screws holding the
convection duct to the oven cavity back plate from
inside of the oven cavity.
14. Lift up the convection duct and release the three (3)
tabs of the oven cavity back plate from the
convection duct.
15. Now, the convection unit assembly is free.
CONVECTION HEATING ELEMENT REMOVAL
1. Remove the two (2) screws holding the convection
heating element to the convection duct.
2. Remove the one (1) screw holding the convection
heater angle to the convection duct.
3. Remove the one (1) screw holding the convection
heater angle and the air separate angle D to the
convection duct.
4. Remove the one (1) screw holding the convection
heater angle A to the convection duct.
5. Remove the convection heating element from the
convection duct.
6. Now, the convection heating element is free.
Screw :
5028 63 98-00/8
Base plate
599 37 42-75