Related Manuals for Hayward HCF302T
Summary of Contents for Hayward HCF302T
- Page 1 LITCF301 Models : HCF302T, HCF342T, HCF343T, HCF343F, HCF362T, HCF363T, HCF363F Models: HCF302 / HCF362 / HCF363...
-
Page 2: Table Of Contents
5.3 Close/ Isolate 6. Changing of the Sand 7. Winterizing 8. Graph of Filter Head Loss 9. Replacement Filter Parts List 10. Warranty 11. Product Registration 12. Warranty Card Registration Commercial Sand Filter Models: HCF302T, HCF342T, HCF343T, HCF343F, HCF362T, HCF363T, HCF363F... -
Page 3: Important Safety Instructions
1. Important Safety Instructions Basic safety precautions should always be followed, including the following: Failure to follow instructions may result in injury. This is the safety-alert symbol. When you see this symbol on your pump or in this manual, look for one of the following signal words, and be alert to the potential for personal injury. - Page 4 Limb Entrapment – A limb inserted into an opening of suction outlet sump or suction outlet cover that is damaged, broken, cracked, missing, or not securely attached can result in mechanical bind or swelling of the limb. Body Suction Entrapment – A differential pressure applied to a large portion of the body or limbs can result in an entrapment.
- Page 5 starting the circulation system. Failure to do so could result in severe personal injury and/ or damage. – Separation Hazard. Failure to follow safety and operation instructions could WARNING result in violent separation of pump components. Strainer cover must be properly secured to pump housing.
-
Page 6: General
Other factors affecting the selection of a filter are the materials used for its construction, the working temperature, and the operating pressure. Hayward® Filters Manufactured from proprietary resins and fiberglass, they are virtually corrosion-proof. The internal fittings (diffuser and lateral system) are manufactured from PVC and ABS. -
Page 7: Installation Characteristics
Disposal of “waste water” must meet local, state and national codes. See Chart on Page 7 for vertical and horizontal clearance. 2.3.3 Piping Connection Kits Hayward Recommended Filter Piping Connections: Filter Model: Port Size Multi-Port Valve Piping Kit Flange P/N 2”... -
Page 8: Characteristics And Dimensions
Filter Area Clearance (Inches) Rate Sand Filter Model Sq. Ft. Sq. M Vertical Horizontal (Lbs) Number 16.5 24.0 30.63 42.5 42.5 30.0 HCF302T 18.75 26.25 34.5 47.5 47.5 34.0 HCF342T 18.75 26.25 34.5 47.5 47.5 34.0 HCF343T 18.5 26.22 34.5 47.5... -
Page 9: Installation
Damages to filters from transportation that are not noted on the bill of lading are not covered by Hayward’s warranty policy and all costs to repair will be the responsibility of the owner. Never put the sand into the filter until it is in its final working position and all prior steps are complete. - Page 10 4.2.1 Tank Positioning Chalk lines are recommended for multiple tank installations and should be laid for positioning each tank. The shipping pallet for the filter also serves as an anchor bolt hole template(s) to aid in positioning the filter tank(s). Attention must be paid to the location and routing of the influent, effluent and waste line plumbing when planning the proper location of the filter system.
- Page 11 Figure 4-1 Anchor Template Dimensions Filter Model: 39” 36” 6” HCF30 42” 40” 6” HCF34 45” 42” 6” HCF36 Position first tank, installing all anchor bolts and secure before positioning the next tank and so on.
-
Page 12: Installation Of The Pressure Gauge
Installation of the Pressure Gauge The pressure gauge assembly will come in a bag hanging from a diffuser within the filter. Remove all the parts from the bag and apply Teflon tape to all threaded connections. Thread the pressure gauge (1) into gauge tee (2). -
Page 13: Testing Of Filter
Run system as normal and check for leaks. If there is a problem with the test, contact Hayward customer service immediately. If sand is added before the test and there is a problem with the filter, the sand will need to be evacuated in order to inspect for potential damage. -
Page 14: Backwash
Use the Hayward 3” Multi-Port valve (HCV375) for the HCF343T and HCF363T filters. Use the Hayward 3” Flange Kit (HCF375KIT) for the HCF343F and HCF363F filters. See section 2.3.3. With the pump turned OFF, arrange the valve(s) for filtration. Start pump, open air relief vent valve until solid stream of water is coming out. - Page 15 8. Graph of Filter Pressure Loss HCF34 HCF30 16.0 16.0 14.0 14.0 12.0 12.0 10.0 10.0 Flow (GPM) Flow (GPM) HCF36 16.0 14.0 12.0 10.0 Flow (GPM) Figure 8-1 Acceptable Pipe Size For Maximum Recommended System Flow Rate Pipe Size Flow Rate GPM Pipe Size Flow Rate GPM...
- Page 16 9. Replacement Part Drawing and Numbers Figure 9-1...
- Page 17 Filter Service Parts List Filter Model Numbers Item No. Qty. Description HCF302T HCF342T HCF343T HCF343F HCF362T HCF363T HCF363F External Air Relief HCXFARV1000 HCXFARV1000 HCXFARV1000 HCXFARV1000 HCXFARV1000 HCXFARV1000 HCXFARV1000 Valve Assembly Pressure Gauge - HCXFPGB1000 HCXFPGB1000 HCXFPGB1000 HCXFPGB1000 HCXFPGB1000 HCXFPGB1000 HCXFPGB1000 1/4"...
-
Page 18: Warranty
All other conditions and terms of the standard warranty apply. Hayward shall not be responsible for cartage, removal and/ or reinstallation labor or any other such costs incurred in obtaining warranty replacements. The Hayward Pool Products warranty does not apply to components manufactured by others. -
Page 19: Product Registration
12. Warranty Card Registration DETACH HERE: Fill out bottom portion completely and mail within 10 days of purchase/installation or register online. Mail to: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207; Attention Warranty Dept Or, register your warranty online at http://www.haywardnet.com...