Activating The Black Stretch; Activating The Mpeg Nr (Noise Reduction); Activating The Dnr (Digital Noise Reduction); Analog Only - Toshiba 32C3000A Owner's Manual

Notes:
• The Tint may only be adjusted on a tape which has been
recorded and played back on an NTSC VCR.
• In the PC input mode (- page 25), Color, Tint and
Sharpness modes are not available.

Activating the black stretch

This function increases the strength of dark areas of the picture
which improves definition.
1
From the Picture settings menu, press V or U to
select Black stretch on the 2nd page.
Picture settings
Black stretch
MPEG NR
DNR
Color Temperature
MENU EXIT
Back
2
Press Y or Z to select On or Off.
Black stretch
Note:
In the PC input mode (- page 25), this mode is not available.

Activating the MPEG NR (Noise Reduction)

If the receiving signal of MPEG is a mosquito (grained) noise
depending on the compression and conversion, the noise may
be reduced when using this function.
1
From the Picture settings menu, press V or U to
select MPEG NR on the 2nd page.
2 Press Y or Z to select Off, Low, Middle or High.
MPEG NR
Note:
In the PC input mode (- page 25), this mode is not available.
Activating the DNR (Digital Noise
Reduction)

- analog only -

If the receiving signal is weak and the picture is blurry, the
picture may be improved when using this function.
1
From the Picture settings menu, press V or U to
select DNR on the 2nd page.
2
Press Y or Z to select Auto, Off, Low, Middle or High.
DNR

Selecting the color temperature

You can change the tone of the picture by selecting from three
preset color temperatures: Cool, Normal or Warm.
1 From the Picture settings menu, press V or U to
select Color Temperature on the 2nd page.
2
Press Y or Z to select mode you prefer.
Color Temperature
Cool: Lends a blue hue to the picture.
Normal: Neutral
Warm: Lends a red hue to the picture.
20
Using the TV's features (General)
2/2
On
Low
Auto
Cool
Watch TV
On
High
Auto
Cool

Adjusting the color management

You can adjust the picture color quality by selecting from 6
base color adjustments : Red, Green, Blue, Yellow,
Magenta or Cyan.
1
Press M, then press Y or Z to display the PICTURE
menu.
2
Press V or U to select 3D Color management, then
press Y or Z, then press Y or Z to select On.
3D Color management
3
Press Q, then press V or U to select Base color
adjustment.
4
Press Q, then press V or U to select an item you want
to adjust.
5
Press Z, then press Y or Z to select Hue, Saturation or
Brightness.
Base color adjustment
Hue
Red
Green
Blue
Yellow
Magenta
Cyan
Reset
MENU Back EXIT
6
Press V or U to adjust the settings as required.
Hue
0
Red
Notes:
• If you select color management Off mode, this mode is not
available.
• In the PC input mode (- page 25), this mode is not
available.

Resetting the base color adjustment

The Reset function adjusts the base color adjustment to the
factory settings.
1
From the Base color adjustment menu, press V or U
to select Reset.
2
Press Q.

Using the active backlight control

In order to improve screen visibility, the active backlight
control sets the screen brightness automatically during dark
scenes.
1 From the PICTURE menu, press V or U to select
Active Backlight Control.
2
Press Y or Z to select On or Off.
On
Saturation Brightness
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
OK
Watch TV
Saturation Brightness
0 0