Table of Contents
Advertisement
If the power indicator doesn't
light green, check the polarity
of the batteries. Check
rechargeable batteries for
a full charge. If you see any
other flashing signal from the
LED, refer to the chart on page
27 to identify the code.
Use the Right Batteries
Your transmitter uses AA
batteries. Use new alkaline
batteries, or rechargeable
batteries such as NiMH
(Nickel Metal Hydride)
batteries in your transmitter.
Make sure rechargeable
batteries are fully
charged according to the
manufacturer's instructions.
If you use rechargeable
batteries in your
transmitter, be aware
that when they begin
to lose their charge, they lose
power more quickly than
regular alkaline batteries.
Caution: Discontinue running
your model at the first sign of
weak batteries (flashing red
light) to avoid losing control.
2, 3
12 • E-MAXX BRUSHLESS
TRAXXAS TQ
RADIO SYSTEM
i
INSTALLING TRANSMITTER BATTERIES
Your TQi transmitter uses 4 AA batteries. The battery compartment
is located in the base of the transmitter.
1. Remove the battery
compartment door by
pressing the tab
and sliding the
door open.
2. Remove the
battery holder.
Install the batteries in
the battery holder. Correct
orientation is indicated in the
battery holder. Make sure the battery
holder is plugged into the transmitter.
3. Reinstall the battery door and snap it closed.
4. Turn on the transmitter and check the "ON" LED for a solid green
light. Note: Switching the transmitter on with your mobile device
installed will automatically launch the Traxxas Link application.
TQi Docking Base Battery Charging Jack
The Docking Base incorporates a standard
charging jack for use with optional
Traxxas rechargeable NiMH battery pack
(#3037) and wall charger (#6545)(each sold
separately). Note: The charger and charging
jack will not charge rechargeable AA
batteries installed in the standard 4-cell AA battery holder supplied
with the TQi. Only use the charger and charging jack with the
#3037 Traxxas NiMH battery.
If the status LED flashes red, the transmitter batteries may be
weak, discharged or possibly installed incorrectly. Replace
with new or freshly charged batteries. The power indicator
light does not indicate the charge level of the battery pack
installed in the model. Note: The Docking Base will charge
your mobile device as long as the transmitter is turned on.
CHARGING THE BATTERY PACK
Your model requires two fully charged battery packs. Two (2)
Traxxas Power Cell NiMH batteries are supplied with your model.
A charger is not included with your model. Traxxas recommends
the #2930 EZ-Peak NiMH charger for quick-charging the included
batteries. See Traxxas.com for more information about chargers
and the EZ-Peak charger. Note: The EZ-Peak charger is NOT
compatible with LiPo batteries.
CHARGING THE BATTERY PACK
Before charging the provided 3-Cell LiPo batteries please read an
understand all safety precautions at the beginning of this manual.
The included chargers can be used to charge the provided battery
packs. The supplied charger has an output rate of 800mAh (0.8
amps), and may require up to seven hours to fully charge a battery.
For faster charging, the optional Traxxas EZ-Peak Plus can charge at
up to 6 amps to reduce charging time to an hour or less. WARNING:
ONLY use a charger designed for LiPo batteries. NEVER charge a
LiPo battery using a NiMH charger, or a NiMH charging mode.
1. Insert the AC power cord into the charger.
2. Insert the AC cord into a wall socket (110-240V). All three LEDs
will light steady green and flash red to indicate the charger is
ready to charge.
3. Plug your Traxxas Power Cell 3-cell LiPo into the charger using
its balance plug. All 3 LEDs will glow steady red. Do not leave
battery and charger unattended while charging.
4. This charger is not designed to charge two packs simultaneously.
If two batteries are plugged into the charger at the same time,
the charger will shut down. Unplug the charger and remove any
installed batteries to reset it.
(Model #3908)
(Model #3908L)
Hide quick links:
Advertisement
Table of Contents
