Summary of Contents for Impex Iron Grip Strength IGS-705
Page 1
Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model IGS-705 Retain This Manual for Reference 07-30-08 OWNER'S MANUAL IRON GRIP STRENGTH WEIGHT BENCH IGS-705 IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746...
ASSEMBLY INSTRUCTIONS... EXPLODED DIAGRAM...………. PARTS LIST…………………………………………………………………………. WARRANTY...… ORDERING PARTS... BEFORE YOU BEGIN Thank you for selecting the IRON GRIP STRENGTH Weight Bench IGS-705 ® by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
Page 4
WRANING LABEL REPLACEMENT The warning label shown here have been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the label in the location shown.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. B.) Secure each end of Cross Brace to each Upright Beam with two M10 x 3 1/8”...
Page 7
STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach the Main Seat Support (#1) to Cross Brace (#2). Secure it with two M10 x 3 1/8” Carriage Bolt (#26), one Bracket (#14), two Ø ¾” Washer (#35), and two M10 Aircraft Nut (#33).
Page 8
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#5) to the Leg Developer Holder (#4). Secure it with one M8 x 2 ¾” Allen Bolt (#29), two Ø 5/8” Washers (#36), and one M8 Aircraft Nut (#34). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel.
Page 9
STEP 4 (See Diagram 4) A.) Attach the Sliding Block (#7) to the Main Seat Support (#3). Secure it with one M10 x 4” Hex Bolt (#30), one Ø ¾” Washer (#35), and one M10 Aircraft Nut (#33). B.) Attach the pivot on the Backrest Support (#9) to the bracket on Main Seat Support. Secure it with one M10 x 3”...
Page 10
Step-5 (See Diagram 5) A.) Attach the Backrest Board (#18) to Backrest Support (#9). Secure it with four M6 x ¾” Hex Bolts (#38) and four Ø ½” Washers (#37). B.) Attach the Seat Pad (#39) onto the Main Seat Support (#3). Secure it with four M6 x 1 ¼” Hex Bolts (#32) and four Ø...
PARTS LIST KEY NO. DESCRIPTION Upright Beam Cross Brace Main Seat Support Leg Developer Holder Leg Developer Bar Catch Sliding Block Incline Adjustment Frame Backrest Support Weight Post Diagonal Support Foam Tube Foam Roll Bracket 1 1/8” x 2 3/8” End Cap Ø...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.