Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Jacuzzi The Cirrus IG
Summary of Contents for Jacuzzi The Cirrus IG
- Page 1 The Cirrus IG Owner's Manual...
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend spa water While the optional spa cover is rigid, it is not designed to temperatures in excess of 104°F. High water temperatures support any weight. Therefore, as a safety precaution, do in excess of 104°F and/or prolonged periods of use can... -
Page 3: Table Of Contents
™ The Cirrus IG Whirlpool Spa Owner's Manual Model D500000 Contents Page Installation Instructions 3-14 Inspection and Shipping Claim Unpacking Indoor Installation, Outdoor installation, Below Ground Outdoor installation, Below Ground (cont). Outdoor Istallation, Ground level or Above Equipment Pack Site Preparation... -
Page 4: Installation Instructions
The Cirrus IG Whirlpool Spa Specifications STANDARD FEATURES OPTIONS 84" 15" TYP. • Three directionally-adjustable jets • Air Blower • Six high volume fully-adjustable jets • Gas Heater 15" • Water Rainbow Fill Spout • Electric Heater TYP. recirculating spout •... -
Page 5: Inspection And Shipping Claim
Inspection and Shipping Claims Check for shipping damage upon receipt of the spa. Jacuzzi Whirlpool Bath is not responsible for damage to the spa sustained during shipping. If damage is evident before unpacking, see instructions regarding shipping claims on the outside of the carton and immediately file a claim with the carrier. -
Page 6: Indoor Installation
Providing natural or forced ventilation of the room will help maintain comfort and minimize moisture damage to the building. Jacuzzi Whirlpool Bath is not responsible for damageresulting from excess moisture or water spillage. Consult an architect or engineer for aid in designing your indoor installation. -
Page 7: Outdoor Installation-Below Ground
INSTALLATION Outdoor Installation-Below Ground The overall length of plumping between the spa and the equipment pack must be less than 20 ft. If you are installing your spa below ground level, the base of the equipment pack must not be more than 9" above the spa rim. Your spa should be installed so that the air intake opening on the air control assembly is not obstructed by backfill or insulating material. -
Page 8: Outdoor Installation, Below Ground (Cont)
INSTALLATION Outdoor Installation — Below Ground (Continued) Support Method If your ground water is high and/or is poor, you will need to build a concrete pad at the bottom of the pit to support your spa and prevent movement and slippage. Build forms for a 60"... -
Page 9: Outdoor Istallation, Ground Level Or Above
INSTALLATION Outdoor Installation — Ground Level or Above You may install your spa and equipment pack so the spa is at ground level or above. The unique characteristic of the equipment pack, which allows your spa system to be located away from the spa itself, is that it is designed to allow flexibility in installation. -
Page 10: Equipment Pack Site Preparation
INSTALLATION Equipment Pack Site Preparation Locate the equipment pack on a level surface (at least 5 feet but not more than 20 feet from the spa) where there is sufficient access to the equipment. Make sure the site selected will allow drainage of water away from the equipment pack. We recommend that you build a concrete pad for the spa equipment. -
Page 11: Electrical Service
You will need to purchase a means of controlling your spa equipment pack. We recommend that you install an air switch/ timer such as that available as an option from your Jacuzzi Whirlpool Bath dealer. Follow switch manufacturer's instructions when installing and refer to addendum sheet included with this product for wiring information. Provide a separate 230 VAC/ 15AMP circuit to supply power to each of the motor/pumps. -
Page 12: Plumbing
INSTALLATION Plumbing 2" PVC ELL AIR VENT VALVE (2) Preliminary Assembly CLEAR PIPE (2) SUCTION Once your equipment pack is installed, attach the suction EQUALIZER equalizer tube assembly provided to the suction inlets of the TUBE ASSEMBLY pumps. Align pump flange ends of the assembly and install using gaskets, bolts and washers provided. -
Page 13: Heater And Air Channel Plumbing
(all types) with a check valve in the line to ensure that the chlorine solution does not enter the heater and cause corrosive damage. Your Jacuzzi Whirlpool Bath dealer will be glad to assist you in making your selection. -
Page 14: Optional Air Blower
The visual effect of the bursting bubbles contributes to the overall hydromassage experience. Consult your Jacuzzi Whirlpool Bath dealer for the air blowers available. The minimum rating of the air blower you use should be 110 cfm, 2.6 psi. For best performance, the blower you select should not exceed this rating by more than 10 percent. -
Page 15: Seat Air Holes
Seat Air Holes Because the air blower is an optional feature of the Cirrus IG, air holes are not factory drilled in the seating area. Included with your spa are an air hole drill guide and a 5/32" diameter drill bit with which to drill the 59 holes required. The drill guide is shaped to fit the contour of the spa. -
Page 16: Spa Set-Up, Alternative Use For Water Rainbow
INSTALLATION Spa Set-Up Remove the protective plastic rim cover on the FRONT ACCESS spa. Use care. Stepping into the spa with shoes SKIMMER/FILTER will scratch the acrylic surface. Remove any packing materials from the spa. SKIMMER BASKET Remove each filter cartridge and skimmer basket from plastic bags. -
Page 17: Operation Instructions
OPERATION Equipment Set-Up Important: Your spa equipment pack must have two professionally installed 230 VAC 15 AMP electrical circuits from your house electrical panel. Additional power will be required for optional equipment, such as heater, air blower, or chlorinator. A proper ground wire run to a ground approved by your local building or electrical inspector is also required. Make sure the equipment is properly bonded as instructed in Installation Instructions. -
Page 18: Priming Procedure I
Then repeat priming procedures steps. PRIMING PROCEDURE 1 (ABOVE WATER LEVEL) SPA RIM BASE EQUIPMENT PACK SHUT-OFF VALVES AND PIPING NOT PROVIDED BY JACUZZI WHIRLPOOL BATH... -
Page 19: Priming Procedure Ii
6 .Turn ON the circuit breaker at the service panel. 7. Turn ON the pumps one at a time. PRIMING PROCEDURE II (BELOW WATER LEVEL) SPA RIM EQUIPMENT PACK BASE SHUT-OFF VALVES AND PIPING NOT PROVIDED BY JACUZZI WHIRLPOOL BATH... -
Page 20: Spa Controls, Normal Operation
(See Safety Information on the inside front cover.) Normal Operation Whirlpool System: DIRECTIONALLY ADJUSTABLE You can enjoy the Cirrus IG spa with or without activating WHIRLPOOL JETS the whirlpool. Either way, bathing in your spa can be pleasurable, as well as therapeutic. After a busy, stressful day, you can look forward to soaking in your spa in still water with no turbulence—only the gentle warmth of the... -
Page 21: Silent Air Induction
OPERATION ™ Water Rainbow The Water Rainbow spout will add the soothing sound of a waterfall to your bathing pleasure, as well as provide a beautiful cascade of shimmering water for an exciting visual effect. Activate the waterfall feature by first turning on the WHIRLPOOL function, then rotate downward the flow con- trol lever located on the left side of the spout. -
Page 22: Maintenance
Obtain a water quality test kit, designed filter cartridge elements will trap most solid materials and especially for spas, from your Jacuzzi Whirlpool bath debris in the water. However, the presence of materials dealer. The test kit must be of the type which allows you... -
Page 23: Water Chemistry
MAINTENANCE Water Chemistry Balancing pH: (continued) Disinfecting: For good hygiene and equipment longevity, maintain the pH of your spa water according to the instructions provided. Add a disinfectant to the water on a regular basis to help pH is the measure to determine if the spa water is too acid control the amount of bacteria, algae and organic materials. -
Page 24: Water Level/Drain
(available from your Jacuzzi Whirlpool Bath dealer or most pool CAUTION Be sure to replace the suction cover imme- supply stores). Follow the manufacturer’s instructions for diately after cleaning. -
Page 25: Automatic Filtration/Maintenance
MAINTENANCE Automatic Filtration/Maintenance The spa should be covered to keep out debris. The filter cycle should be run at least two hour per day to maintain water quality. If your equipment pack has a timer installed, the timer may turn on the filter automatically each day for you in your absence. Your timer may also function to turn on the heater to maintain a certain water temperature. -
Page 26: Cleaning Your Spa
Meguiar’s #10 Mirror Glaze, which is a product specifically Jacuzzi Whirlpool Bath does not guarantee or warranty designed for use on acrylic finishes. If Meguiar’s is not this cover. Refer to spa cover manufacturer's informa- available, an acrylic polish of equal quality or automotive tion provided with the cover. -
Page 27: Troubleshooting Guide
Damaged or worn motor bearings. Impeller rubbing inside case. Debris inside pump. * Note: The skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your Jacuzzi Whirlpool Bath Authorized Service Agent or Dealer. - Page 28 Fill spa to middle of skimmer opening. Faulty check valves. Replace valves. * Note: The skills and tools necessary for the safe repair of this spa require the services of qualified service personnel. Contact your Jacuzzi Whirlpool Bath Authorized Service Agent or Dealer.
- Page 29 Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of this product. Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.