Mitsubishi Electric FR-A701 Instrucion Manual page 191

Outline dimension drawings
Dedicated motor (SF-V5RU(H)) outline dimension drawings (standard horizontal type with brake)
Frame Number 112M, 132S, 132M
SF-V5RU(H) ,
3KB 5KB 7KB
Connector (for encoder)
MS3102A20-29P
Terminal box for cooling fan
A
Suction
1
2
Direction of
cooling fan wind
Mark for earthing
(grounding)
Earth (ground)
terminal (M5)
Frame Number 160M, 160L, 180M, 180L
SF-V5RU(H) ,
11KB 15KB 18KB 22KB
Terminal box for cooling fan
Connector (for encoder)
MS3102A20-29P
L
A
KA
Exhaust
Suction
1, 2
Direction of
Mark for earthing
cooling fan wind
(grounding)
F
Earth (ground)
terminal (M8)
W Sliding distance
S
Frame leg viewed
Section AA
Dimensions table
SF-V5RU SF-V5RU SF-V5RU SF-V5RU Frame
K K1 K3 K4 No.
3 — — — 112M
5 3 — — 132S
7 5 3 — 132M
11 7 5 — 160M
15 11 7 3 160L
18 — — —
180M
22 15 11 —
— 18 15 5 180L
30 — — 7
200L
37, 45 22, 30 18, 22 —
— 37 30 11, 15 225S
Note) 1. Install the motor on the floor and use it with the shaft horizontal.
2. Leave an enough clearance between the fan suction port and wall to ensure adequate cooling.
Also, check that the ventilation direction of a fan is from the opposite load side to the load side.
3. The size difference of top and bottom of the shaft center height is
4. The 400V class motor has -H at the end of its type name.
5. Since a brake power device is a stand-alone, install it inside the enclosure.
(This device should be arranged at the customer side.)
184
,
L
KL
R
B Q
KA
Main
Exhaust QK
terminal box
A
A
J
F F XB
E
N
W
S
Section AA
, ,
R
KL
B 110
D
Main
90
1
terminal box
A
A
J
F
XB
E
E
N
M
X
Main terminal box
from above
U V
B1 B2 G1 G2
For brake (B1, B2)
Mass
(kg)
A B C D E F G H
53 355 135 112 228 95 70 6.5 —
70 416 152 132 266 108 70 6.5 —
80 435 171 132 266 108 89 6.5 —
140 522.5 198 160 318 127 105 8 —
155 544.5 220 160 318 127 127 8 —
185
568.5 225.5 180 363 139.5 120.5 8 —
215
255 587.5 242.5 180 363 139.5 139.5 8 —
305
644.5 267.5 200 406 159 152.5 11 —
330
395 659 277 225 446 178 143 11 —
0
-0.5
D
1
Main terminal box
2
B1
E
M
ML
Sliding distance
X
Frame leg viewed
from above
Frame Number 200L
SF-V5RU(H)
30KB 37KB 45KB
Connector (for encoder)
MS3102A20-29P
Suction
2
1, 2
Mark for earthing
Direction of
(grounding)
cooling fan wind
Earth (ground)
terminal (M12)
Terminal box for cooling fan
For motor (U, V, W)
For cooling fan (A, B, C)
Earthing
(grounding)
A B C
W
terminal (M8)
Earthing (grounding)
terminal (M4)
For thermal protector (G1, G2)
Motor
I J KA KD KG KL KP L M
— 40 69 27 93 242 290 555 230 242 180
— 40 75 27 117 256 329 655 256 268 180
— 40 94 27 117 256 329 693 256 268 218
— 50 105 56 115 330 391 845.5 310 — 254
— 50 127 56 115 330 391 889.5 310 — 298
— 50 127 56 139 352 428 920 335 — 285
— 50 146 56 139 352 428 958 335 — 323
— 70 145 90 487 — 546 1070 390 — 361
— 70 145 90 533 — 592 1091 428 — 342
Terminal box for cooling fan
For brake (B1, B2)
For motor (U, V, W)
For thermal protector (G1, G2)
For cooling fan (A, B)
B2 U V W G1 G2
A B C
Earthing (grounding)
terminal (M4)
, ,
Terminal box for cooling fan
L
A R
140
B
KA
φ22 110
Main
terminal box
Exhaust
1
A
A
XB
F F
N
W
S
Section AA
indicates an inserting position of a bolt with hex
head holes for manual opening.
Make sure to earth the earth terminal of the frame
installation foot as well as the earth terminal in the
terminal box.
Shaft End
ML N X XB Z Q QK R S
4 70 12 60 45 200 28j6
4 89 12 80 63 239 38k6 8
4 89 12 80 63 258 38k6 8
4 108 14.5 110 90 323 42k6 8
4 108 14.5 110 90 345 42k6 8
4 121 14.5 110 90 351.5 48k6 9
4 121 14.5 110 90 370.5 55m6 10
4 133 18.5 140 110 425.5 60m6 11
4 149 18.5 140 110 432 65m6 11
Earthing (grounding)
terminal (M4)
D
2
J
E E
M
Sliding distance
X
Frame leg viewed
from above
(Unit: mm)
Terminal Screw Size
T U W U,V,W A,B,(C) G1,G2 B1,B2
7 4 8 M6 M4 M4 M4
5 10 M6 M4 M4 M4
5 10 M6 M4 M4 M4
5 12 M8 M4 M4 M4
5 12 M8 M4 M4 M4
5.5 14 M8 M4 M4 M4
6 16 M8 M4 M4 M4
7 18 M10 M4 M4 M4
7 18 M10 M4 M4 M4