Kenwood VR-506 Instruction Manual page 20

-"'
q
input fhe distance to the speakers
0 Measure the distance from the listening position to each of the
speakers
Jot down the distance to each of the speakers
Distance to front speakers: _ feet- meters
Distance to center speaker: _ feet- meters
Distance to surround speakers: _ feet- meters
0 Use the MULTI CONTROL keys to select the distance to the
front speakers
The speaker indicator to be adjusted blinks
Indication in feet indication in meters
l
The allowable setting range is 1 to 30 feet (0 3 to 9 0 m), adjustable
in 1 foot (0 3 m) increments
0 Press the SET UP key to accept the settings
0 Repeat steps 0 and 0 to input the distance for each of the
speakers
0 Setup is complete when the input indication reappears
Display when all speakers have been selected
l
The speakers you have selected should appear on the display
Confirm that all the speakers have been correctly selected
If the input level of an analog source signal is too high, adjust the input
level The CLIP indicator will blink to indicate the source signal
@ Use the INPUT SELECTOR knob to select the source which
input level you want to adjust
l
You can store a separate input level for each input source If the
MONITOR function is ON, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources
0 Press the SOUND key repeatedly until the "INPUT" indication
appears
0 Use the MULTI CONTROL keys to adjust the input level
l
The adjustment mode is displayed for approximately eight seconds
l
The input level may be adjusted to any one of three settings: OdB,
-3dB, and -6dB (The initial setting is OdB )
0 Press the SOUND key again to return to the input indication
Preparifg for playback
Some preparatory steps are needed before starting playback
INPUT MODE
UTO/CINEMA EQ
KRF-V6050D/ 'OVirER
INPUT StfLECTOR
v505olx
SPEAKERS AIB
V5550D
(SPEAKER/MUTE)
&zlecfin# the input made
If you have selected a component connected to the CDIDVD, DVD/Gch,
DVD (VR-50MKRF45550D only) or VIDE02/MONITOR jacks, make
sure that the input mode setting is correct for the type of audio signal to
be used
-La
sf?tecthrff ~0~~~~
Select the source name corresponding to the component connected to
the MD/TAPE jacks The initial factory setting is "TAPE" To change the
source to "MD," follow the steps below:
0 Use the INPUT SELECTOR knob to select "TAPE"
0 Hold down the AUTO/CINEMA EQ key for more than 2 seconds
l
The source indication changes to "MD"
l
To return to the original indication, repeat procedure 8
Selecling fhe speaker system fVR-5~6~R~-V6U5U~ ottiyj
Press the SPEAKERS A or B key to select the speaker system to
be used
AON : Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel
BON : Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel
A+B ON : Sound from both the speakers connected to the
SPEAKERS A and B terminals on the rear panel
A+B OFF : No sound from the speakers Use this setting when
listening with headphones for stereo sound and virtual
surround in all playback modes
The indicator for the speakers
you want to use should be lit
The speaker indicator lights
VR-506/KRF-V6050D
VR-505/517/KRF-V5050D/
V5550D
l
Selecting "6ch INPT" by pressing the INPUT MODE key, whereby "DVD/
6ch" is the input source will cause SPEAKER A to be selected automati-
cally
On the VR-505/517/KRF-V5050DN5550D, press the SPEAKER key to
switch the speakers on and off
Turning on the receiver
0 Turn on the power to the related components
0 Turn on the power to this receiver by pressing POWER (and ON/
STANDBY) key(s)