Page 1
Yes, You Can.® Invacare® TDX SP Electric wheelchair Operating manual...
Page 2
How can you get in touch with Invacare®? If you have any questions or need support, please contact your authorised Invacare® Dealer, who has the necessary know-how and equipment plus the special knowledge concerning your Invacare® product, and can offer you all-round satisfactory service. Should you wish to contact Invacare® directly, you can reach us in Europe at the following addresses and phone numbers.
Page 3
Bridgend Industrial Estate uk@invacare.com Mid Glamorgan - CF31-3PY eire@invacare.com United Kingdom WWW: www.invacare.co.uk Invacare Mecc San s.r.l. +39 - 0445 - 38 00 59 Via Dei Pini, 62 Fax: +39 - 0445 - 38 00 34 I - 36016 Thiene (VI) italia@invacare.com...
Page 4
+31 - (0)318 - 69 57 57 Celsiusstraat 46 Fax: +31 - (0)318 - 69 57 58 NL-6716 BZ Ede csede@invacare.com The Netherlands WWW: www.invacare.nl Invacare® PORTUGAL Lda +351-225105946 Rua Senhora de Campanhã 105 Fax: +351-225105739 P-4369-001 Porto portugal@invacare.com PORTUGAL WWW: www.invacare.pt...
Table of Contents Chapter Page Introduction Important symbols in this manual ..................12 Important symbols found on the vehicle ................13 Type classification and permissible use................14 Guarantee ..........................14 Indications..........................15 Life expectancy........................15 Safety Notes General Safety Notes ......................16 Safety information with regard to care and maintenance ...........19 Safety Information on Electromagnetic Interference............20 Safety Information on Driving and Freewheel Mode............21 Safety information on maintenance work and alterations to the wheelchair....23...
Page 6
5.3.1 The ”SureStep“ System ....................29 5.3.2 Maximum obstacle height .....................29 5.3.3 Safety information when ascending obstacles .............30 5.3.4 The correct way to overcome obstacles ...............31 Driving up and down gradients....................32 Pushing the wheelchair by hand Disengaging motors........................33 The Shark II Remote Assembly of the remote......................34 Battery charging display......................36 Adjusting speed........................37...
Page 7
8.1.4 Setting the height of the parallel sliding armrests............52 8.1.5 Adjusting the angle of the armpad on the parallel sliding armrests......53 8.1.6 Setting the width of the side sections ................54 Manually adjusting the seat tilt ....................56 Manually adjusting the backrest ....................57 8.3.1 Adjusting backrest using perforated plate ..............57 8.3.2...
Page 8
9.2.2.8 Adjusting the angle adjustable foot plate..............83 9.2.2.9 Adjusting the angle and depth adjustable foot plate ..........84 9.2.3 Manually height adjustable legrest 80° - 0° with ergonomic length adjustment ...85 9.2.3.1 Swivelling the legrest outward and/or removing............85 9.2.3.2 Setting the angle......................86 9.2.3.3 Adjusting the length of the legrest ................88 9.2.3.4...
The decision whether the model is suitable for the user may only be taken by medical specialists with appropriate expertise. Invacare® or their statutory representatives can accept no liability in cases in which the wheelchair has not been adapted to suit the users’ handicaps.
Page 11
This manual contains copyrighted information. This manual may not be reproduced or reprinted either partly or completely without previous written consent from Invacare® or its statutory representatives. We reserve the right to make any necessary alterations on the grounds of...
Important symbols in this manual WARNING! This symbol warns you of danger! • Always follow these instructions to avoid injury to the user or damage to the product! EXPLOSION HAZARD! This symbol warns you of an explosion hazard, an example of which can be caused by excessive tyre pressure in a pneumatic tyre! •...
Important symbols found on the vehicle This product has been supplied from an environmentally aware manufacturer that complies with the Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/CE. This product may contain substances that could be harmful to the environment if disposed of in places (landfills) that are not appropriate according to legislation.
Type classification and permissible use This vehicle was designed for persons whose ability to walk is impaired, but who are still physically and mentally able to operate an electric vehicle. It has been classified according to EN 12184 as a class B mobility product (for indoor and outdoor areas).
Indications The use of this mobility product is recommended for the following indications: The inability or a greatly restricted ability to walk within the scope of the basic requirement to be able to move within one’s own four walls. The need to leave the dwelling place in order to get some fresh air during a short walk or to reach those places generally to be found at close distance to the dwelling and where everyday business is carried out.
Safety Notes • READ WELL BEFORE OPERATION! General Safety Notes Danger of injury if wheelchair is used in any other way than the purpose described in this manual! • Only ever use the wheelchair in accordance with the instructions in this User's Manual! •...
Page 17
Danger of injury if the wheelchair is switched off while driving, for example by pressing the On/Off Button or disconnecting a cable, due to it coming to an abrupt, sharp stop! • If you have to brake in an emergency, simply release the joystick which will bring you to a halt! Danger of injury when transferring wheelchair to a vehicle for transport with the occupant seated in it! •...
Page 18
Danger of fire or breaking down due to electric devices being connected! • Do not connect any electric devices to your wheelchair that are not expressly certified by Invacare® for this purpose! Have all electrical installations done by your authorised Invacare® Dealer!
Safety information with regard to care and maintenance Danger of accident and loss of guarantee if maintenance is insufficient! • For reasons of safety and in order to avoid accidents which result from unnoticed wear, it is important that this electric vehicle undergoes an inspection once every year under normal operating conditions (see inspection plan contained in service instructions)! •...
Safety Information on Electromagnetic Interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference (EMI) Regulations. However, electromagnetic fields, such as those generated by radio and television transmitters, and cellular phones, can influence the functions of electric vehicles.
Safety Information on Driving and Freewheel Mode Danger of injury if the wheelchair tips over! • Only ever negotiate gradients up to the maximum safe slope (see chapter "Technical Specifications" starting on page 119) and only with the backrest and seat tilt (if fitted) in an upright position! •...
Page 22
Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated area! • If you are a user with severely limited mobility, we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant! Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion! •...
Safety information on maintenance work and alterations to the wheelchair WARNING: Danger of injuries and damage to the wheelchair, in case the suspension is adjusted without the immobilisation mechanism of the front anti-tippers being re- adjusted! • When the hardness of the suspension is adjusted, the immobilisation mechanism of the front anti-tippers must without fail be checked and, if necessary, also re-adjusted!
Key features 1) Push handle 2) Armrest 3) Lever for disengaging a motor (only visible on right-hand side of picture) 4) Drive wheel 5) Remote 6) Legrests...
Getting in and out of the wheelchair Important information when side transferring in and out of the wheelchair In order to side transfer it is necessary for the armrest to either be raised or removed completely depending on the model. A skirtguard can be installed as an option in connection with the parallel sliding armrest.
Raise the parallel sliding armrest / remove the skirtguard (optional) Swivelling the armrest up • Swivel the armrest up to access from the side. Removing the skirtguard (optional) to get on: • Release wing nut (1) . • Remove the skirtguard from the receptacle.
Page 27
Getting into the wheelchair: • Position your wheelchair as close as possible to your seat. This might have to be done by an attendant. • Switch your wheelchair off. • Apply the hand brake of your wheelchair (if existing). • Detach the side part of your wheelchair or swivel it up. •...
Driving Before driving for the first time... Before you take your first trip, you should familiarise yourself well with the operation of the vehicle and with all operating elements. Take your time to test all functions and driving modes. NOTE: If installed, make sure to properly adjust and use the posture belt each time you use the wheelchair.
Parking and stationary When parking your vehicle or if your vehicle is stationary for a prolonged period: • Switch the vehicle's power system off (ON-/OFF key). • Activate your anti-theft lock, if existing. Taking Obstacles 5.3.1 The ”SureStep“ System This electric wheelchair is fitted with "SureStep" technology. When climbing over obstacles, the front steering wheels are raised using the torque generated by the drive wheels.
5.3.3 Safety information when ascending obstacles CAUTION: Danger of Tipping Over! • Never approach obstacles at an angle! • Put your backrest into an upright position before climbing an obstacle! CAUTION: The wheelchair can be damaged if an obstacle is approached at excessive speed.
5.3.4 The correct way to overcome obstacles Ascending and descending Right The same approach applies to both ascending and descending obstacles: • Approach the obstacle or the kerb slowly and at a right angle. • Stop shortly before the front wheels come into contact with the obstacle. Wrong •...
Driving up and down gradients For information concerning the maximum safe slope, please see chapter "Technical Specifications" starting on page 119. WARNING: Danger of tipping over! • Only ever drive downhill at a maximum of 2/3 of the top speed! Avoid sudden changes of direction or abrupt braking when driving on slopes! •...
Pushing the wheelchair by hand The motors of the wheelchair are equipped with automatic brakes, preventing that the wheelchair starts rolling out of control when the joystick box is switched off. When pushing the wheelchair, the magnetic brakes must be disengaged. Disengaging motors Danger of the vehicle running away! •...
The Shark II Remote Assembly of the remote Top side (standard) Battery charging display ON/OFF button Activate / connect through / deactivate adjusting mode Reduce travel speed Travel speed display Horn Increase travel speed LED for “control unit activated for accompanying person“...
Page 35
Top side (including light option) 11) Warning indicator 12) Left hand indicator 13) Light 14) Right hand indicator 15) LED for “light activated“ Lower side 1) Combined charging socket / programming socket...
Battery charging display • Battery charging All diodes illuminated: full range! display • Only the yellow and red diodes are illuminated: Reduced range! Charge batteries before a longer trip! • Only the red diodes are illuminated: Very low range! Charge batteries as soon as possible! •...
Adjusting speed The user can adjust the chair’s top speed to suit their preferences and environment. The currently selected top speed is shown on the Speedometer and can be adjusted using the “Increase Speed” (2) and “Reduce Speed” (1) buttons. Using the speedometer Each of the speedometer’s 6 large LEDs typically represent 0%, 20%, 40%, 60%, 80% and 100% of the chair’s maximum speed.
“5 Speed” and “VSP” modes Shark II supports 2 modes of top speed adjustment – “5 Speed” and “VSP” modes. In the “5 Speed” mode pressing the Increase Speed and Decrease Speed buttons steps between one of the 5 top speeds 20% to 100%. In the “VSP”...
Status display The status display serves to display error messages. For error codes see chapter "Error Codes and Diagnostic Codes" on page 46. Activate/de-activate the immobiliser Activate the immobiliser Activate • Whilst the remote is switched on, press and hold the ON/OFF button (1) for 4 seconds.
• Invacare® supplies all electric vehicles from the factory with a standard drive programme. Invacare® can only assume a warranty for the safe vehicle handling of the electric vehicle – in particular tipping stability - for this standard drive programme! Will the wheelchair not drive after switching on? Check the drive-away lock (see chapter "Activate/de-activate the immobiliser "...
7.8.1 How a wheelchair with "Indirect Steering" reacts to joystick movements. "Indirect Steering" occurs by individually applying power to the drive wheels, and is found on wheelchairs with front, rear and middle wheel drive. Travel direction The further the joystick is moved in a particular direction, the more dynamically the wheelchair reacts.
7.8.2 Operating the electric adjustment options Electric adjustment options are operated using the joystick. • Press the adjustment mode button once in order to activate the first adjustment option. Press the adjustment mode button twice in order to activate the second adjustment option.
Control unit for an accompanying person (option) The control unit for an accompanying person enables the control of the wheelchair to be handled by an accompanying person. 7.9.1 Layout of the remote Joystick Change over control unit to accompanying person/occupant Activate/connect through/deactive adjustment mode Set travel speed...
7.9.2 Operating the electric adjustment options Electric adjustment options are operated by means of the joystick. The control unit must be switched over to ’accompanying person’ for the adjustment options to be operated via the control unit for the accompanying person. •...
7.10 Error diagnosis If the electronic system shows a failure, please use the following guide to locate the fault. NOTE: Ensure that the drive electronics system is switched on before starting any diagnosis. If the status display is OFF: Check whether the drive electronics system is SWITCHED ON. Check whether all cables are correctly connected.
7.11 Error Codes and Diagnostic Codes FLASH FAULT EFFECT Comments CODE User error or drive Stops driving • Ensure that the joystick is in the neutral motors overloaded central position (simply release the joystick) and switch on again. • Drive motors overloaded. Shut electronics down and then switch on again.
Page 47
FLASH FAULT EFFECT Comments CODE Error in Shark Stops driving • Check remote bus cable and all remote connecting plugs. • Replace remote. Error in Shark Stops driving • Check all cables and connecting plugs in power module the Shark system. •...
Adjusting the wheelchair to the user's seating posture WARNING: Danger of damage to the wheelchair and of accidents! With some combinations of adjustment options, collisions can occur between the legrest and the chassis or between the foot plates and the ground!This occurs in particular on wheelchairs with a lifter! •...
Adjusting the armrests and the joystick box 8.1.1 Adapting the remote to the length of the user’s arm Requirements: • Allen key 3 mm • Loosen the socket head screw (1). • Set remote to the desired length by pushing forward or backward.
8.1.2 Setting the height of the remote • Loosen one or both of the wing screws (1 and 2) that allow height adjustment of the joystick box. • Adjust the joystick box to the desired height. • Re-tighten the screw(s).
8.1.4 Setting the height of the parallel sliding armrests Requirements: • Allen key 2 mm • Loosen the screws (1) with the 2 mm Allen key on both sides of the spindle. • Turn the spindle clockwise (A). The armrest is raised.
8.1.5 Adjusting the angle of the armpad on the parallel sliding armrests Requirements: • Allen key 4 mm • Open-end spanner 10 mm • Loosen the screw (1, on the inner side of the armrest), which allows adjustment of the angle of the armpad, while countering the nut (2, outer side of the armrest) with the...
8.1.6 Setting the width of the side sections The distance between the side sections can be adjusted by 5.5 cm on both sides (11 cm in total). Requirements: • Allen key 8 mm Where to find the adjustment screws The figure below shows the position of the screws (1) which allow armrest width adjustment (only the left side is shown in the illustration).
Page 55
Doing the adjustment • Loosen screw (1) • Adjust armrest to required position. • Retighten the screw. • Repeat this procedure for the second armrest.
Manually adjusting the seat tilt The seat angle is adjusted using two perforated plates which are located right and left under the seat frames. Requirements: • 1x jaw spanner 1/2 inch The figure to the right shows the position of the bolts (1) for manual seat angle adjustment.
Manually adjusting the backrest 8.3.1 Adjusting backrest using perforated plate • Unscrew the hand screws (1) on both sides. • The backrest is adjusted by choosing a combination of one of the two bore holes in the backrest frame and one of the six bore holes in the fixing plate.
Adjusting footrests and legrests Centre-mounted legrests 9.1.1 Electric legrest The electric legrest is operated via the remote. Please see chapter "Operating the electric adjustment options" on page 42. The electric legrest can be lowered completely to assist getting out of the wheelchair. To do so, move your seat into the correct position by lowering the lifter or by means of a negative seat angle (tilted slightly to the front).
9.1.1.1 Lowering the electric legrest completely to assist getting out of the wheelchair Warning! Misuse may destroy the legrest. • Please read and carefully follow the instructions below. Getting in/out of the wheelchair • Set the lifter and tilt to a comfortable position. •...
Page 61
Lifting up the footplates • You are sitting in the wheelchair. • Put your feet beside the footplates. • Pull the lever (1). The footplates rise up automatically. • Let go the lever (1) and put your feet on the footplates.
Page 62
Warning! Danger of damage to the legrest! • Always make sure that the footplates are fully raised to the uppermost position before adjusting the angle of the legrest! • Disregarding this advice will cause damage to your legrest. Adjusting the legrest •...
9.1.2 Adjustable legrest 9.1.2.1 Adjusting the angle Prerequisites: • 1x 10 mm open-ended spanner • Use the open-ended spanner to loosen the counternut (1). • Move the legrest to the desired position by turning the spindle (2). • Tighten the counternut.
9.1.2.2 Adjusting the length of the legrest Prerequisites: • 1x 5 mm socket head spanner • Use the socket head spanner to loosen the fastening screws (1). • Slide the foot support to the desired height. • Tighten the fastening screws.
9.1.2.3 Adjusting the calf plate to the calf width of the user The calf plate of the legrest can be adapted to the user’s calf width by bending apart or together. • Bending the calf plate to the desired width.
9.1.2.4 Adjusting the angle of the foot plate Prerequisites: • 1x 5 mm socket head spanner • Fold up the foot plates in order to access the adjusting screws. • Use the socket head spanner to adjust the adjusting screws (1). •...
Laterally mounted legrests 9.2.1 Standard footrest with pre-set angle 9.2.1.1 Swivelling the footrest outward and/or removing The small unlocking button is located on the upper section of the footrest. When the footrest is unlocked, it can be swivelled inward or outward when getting into the wheelchair as well as being removed completely.
9.2.1.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that there is an adequate distance between the legrests and the steering wheels or the ground! Pre-requisites: •...
Page 69
• Loosen the screw (1) using the Allen key. • Set the desired angle. • Re-tighten the screw.
9.2.1.3 Setting the end stop of the footrest Pre-requisites: • 1x 6 mm Allen key • 1x 10 mm open-ended spanner The end position of the footrest is determined by means of a rubber stop (1). The rubber stop can be screwed in or out (A) or pushed up or down (B).
Page 71
• Use the Allen key to loosen the screw (1) and swivel the footrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
Page 72
• Move the rubber stop to the desired position • Re-tighten the counternut • Move the footrest to the desired position. • Re-tighten the screw.
9.2.1.4 Adjusting the length of the footrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that there is an adequate distance between the legrests and the steering wheels or the ground! Pre-requisites: •...
9.2.2 Manually height adjustable legrest 90° - 0° 9.2.2.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.
9.2.2.2 Setting the angle PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that there is an adequate distance between the legrests and the steering wheels or the ground! •...
9.2.2.3 Setting the end stop of the legrest Pre-requisites: • 1x 10 mm open-ended spanner The end position of the legrest is determined by means of a rubber stop (A). The rubber stop can be screwed in or out (A) or pushed up or down (B).
Page 77
• Disengage the release handle (1) and swivel the legrest upward in order to access the rubber stop. • Use the open-ended spanner to loosen the counternut (1).
Page 78
• Move the rubber stop to the desired position • Re-tighten the counternut • Move the footrest to the desired position. • Re-tighten the release handle.
9.2.2.4 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that there is an adequate distance between the legrests and the steering wheels or the ground! Pre-requisites: •...
9.2.2.5 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.
9.2.2.6 Adjusting the height of the calf plate Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.
9.2.2.7 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.
• Lift leg over the heel strap and place on the ground. 9.2.2.8 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...
9.2.2.9 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...
9.2.3 Manually height adjustable legrest 80° - 0° with ergonomic length adjustment 9.2.3.1 Swivelling the legrest outward and/or removing The small unlocking button is located on the upper section of the legrest. When the legrest is unlocked, it can be swivelled inward or outward when getting into wheelchair as well as being removed completely.
9.2.3.2 Setting the angle PLEASE NOTE: Danger of crushing! • Do not reach inside the swivelling range of the legrest! PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that there is an adequate distance between the legrests and the steering wheels or the ground! •...
Page 87
• Lowering: Keep the legrest in the foot plate area, pull the lateral adjusting lever (1) and lower the legrest slowly.
9.2.3.3 Adjusting the length of the legrest PLEASE NOTE: Danger of injury due to incorrect adjustment of the footrests and legrests. • Before and during every journey it is imperative to ensure that there is an adequate distance between the legrests and the steering wheels or the ground! Pre-requisites: •...
9.2.3.4 Adjusting the depth of the calf plate The depth of the calf plate can be adjusted via the holding plate. The holding plate hole combinations allow 5 different depth settings. Pre-requisites: • 1x 10 mm open-ended spanner • Use the open-ended wrench to loosen the nut (1) and remove.
9.2.3.5 Adjusting the height of the calf plate Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the screws (1). • Adjust to the desired position. • Re-tighten the screws.
9.2.3.6 Unlocking and swivelling the calf plate backward when alighting • Press the calf plate straight down. • Unlock the legrest and swivel outward. The calf plate swivels backward on its own.
• Lift leg over the heel strap and place on the ground. 9.2.3.7 Adjusting the angle adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen both set screws on the foot plate. •...
9.2.3.8 Adjusting the angle and depth adjustable foot plate Pre-requisites: • 1x 5 mm Allen key • Use the Allen key to loosen the set screw on the foot plate (1). • Adjust the foot plate to the desired angle or depth. •...
Electrical System 10.1 Electronics Protection System The vehicle's electronics are equipped with an overload-protection system. If the motors are put under considerable strain for a longer period of time (for example, when driving up a steep hill) and especially when the ambient temperature is high, then the electronic system could overheat.
NOTE A defective main fuse may be replaced only after checking the entire electric system. An Invacare® specialised dealer must perform the replacement. You can find information on the fuse type in chapter "Technical Specifications" starting on page 119. All electrical equipment fitted to the wheelchair is protected against overload by the main fuse.
10.2 Batteries 10.2.1 What you need to know about batteries Power is supplied by two 12V gel batteries. The batteries are maintenance-free and only need regular charging. New batteries should always be fully charged once before their first use. New batteries will be at their full capacity after having run through approx.
Page 97
The batteries cannot be overcharged with the specified charger. Please use only charging devices in Class 2. This class of chargers may be left unattended during charging. All charging devices which are supplied by Invacare® comply with these requirements.
Danger of explosion and destruction of batteries if the wrong battery charger is used! • Only ever use the battery charger supplied with your vehicle, or a charger that has been approved by Invacare®! Danger of electric shock and damage to the battery charger if it is allowed to get wet! •...
Page 99
Charging the batteries • Switch off the wheelchair at the Joystick Box. • Connect the battery charger to the Joystick Box - the charging socket is located on the bottom of the Joystick Box (1). • Connect battery charger to the mains outlet and switch on if necessary.
10.2.3 Removing and fitting batteries WARNING: Danger of injury if the batteries are not handled correctly during assembly and maintenance work! • New batteries should be installed by authorised technicians! • Observe the warnings on the batteries! • Take into account the heavy weight of the batteries! •...
10.2.3.1 Removing the batteries CAUTION: Risk of fire and burns if battery poles are bridged! • When replacing the batteries the battery poles MUST NOT come into contact with metal parts of the wheelchair causing bridging. • Be sure to replace the battery pole caps after the batteries have been replaced. WARNING: Risk of fire and burns due to damage to the battery cables! •...
Page 102
• Remove the side-mounted legrests if fitted. A centrally-fitted, manually adjustable legrest should be put in its top position by turning the spindle (1). • Remove the screws on the panelling (1) using the 1/4" Allen key.
Page 103
• Remove the panelling. • Pull the batteries forwards out of the slide.
Page 104
• Remove the terminal cover from the battery terminals (1). • First undo the bolt on the negative terminal (black cable) with the 11 mm jaw spanner. • After this, undo the bolt on the positive terminal (red cable). CAUTION! Danger of crushing! •...
• Only ever transport damaged batteries in an appropriate acid-resistant receptacle. • Wash all objects that have come into contact with acid with lots of water. Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare®.
Care and maintenance NOTE: Have your vehicle checked once a year by an authorised Invacare® dealer in order to maintain it's driving safety and roadworthiness. Cleaning the vehicle When cleaning the vehicle, pay attention to the following points: • Only use a damp cloth and gentle detergent.
Page 107
Maintenance Jobs Seat and backrest padding: - Check for perfect condition. Side part and armrest: - Are all fastening elements installed? - Can armrests / side parts be removed and installed without too much physical effort? - Are armrests secured in their positions? Legrests: - Do legrests lock into place without any problem (only applies to detachable legrests)?
Page 108
- Clean all parts carefully. When necessary Once a year you should have your wheelchair inspected and serviced by your authorised dealer. A complete checklist of necessary maintenance work can be found in the Service Manual, which can be obtained from Invacare®.
Transport 12.1 Transferring the wheelchair to a vehicle WARNING: Danger of tipping over, if the wheelchair is transferred to a vehicle using a ramp that exceeds the maximum safe slope, or if the backrest is not in an upright position during transfer! •...
These accessories are not included in the standard scope of wheelchair order and delivery, but can be obtained from Invacare as an option. This electric wheelchair complies with the requirements of ISO 7176/19-2001 and may be used as a vehicle seat in connection with an anchoring system that has been checked and approved in accordance with ISO 10542.
Page 111
Caution: There is a danger of injury if the wheelchair is not properly secured during use as a vehicle seat! • If possible, the user should always leave the wheelchair to use a vehicle seat and the seatbelts provided with the vehicle! •...
12.2.1 How the wheelchair is anchored in a vehicle for use as a vehicle seat The electric wheelchair is fitted with four anchoring points, which are labelled with the symbol shown on the right. Snap hooks or belt loops can be used for fixation.
12.2.2 How the user is secured within the wheelchair Caution: there is a danger of injury if the user is not properly secured within the wheelchair! • Even if the wheelchair is fitted with a securing belt, this is no substitute for a proper seatbelt in a travelling vehicle! Always use the transport vehicle seatbelt! •...
Page 114
Seat belts may not be held at a distance The pelvic belt should be positioned in the from the user's body using parts of the area between the user's pelvis and thighs wheelchair such as armrests or wheels. so that it is unobstructed and not too loose. The ideal angle of the pelvic belt to the horizontal is between 45°...
Page 115
The safety belt of the transporting vehicle should be applied as shown in the illustration at right. 1) Centre line of the body 2) Centre of the sternum...
12.3 Securing the wheelchair for transport without passengers CAUTION: Injury hazard! • If you are unable to fasten your electric wheelchair securely in a transport vehicle, we recommend that you do not transport it! • Before transporting your wheelchair, make sure the motors are engaged and that the Joystick Box is switched off.
• Cleaning and disinfection. Please see chapter "Care and maintenance" on page 106. • Inspection according to service plan. Please consult service instructions, available from Invacare®. • Adaptation to the user. Please see chapter "Adjusting the wheelchair to the user's seating...
Page 118
Disposal • The equipment wrapping is potentially recyclable. • The metal parts are used for scrap metal recycling. • The plastic parts are used for plastic recycling. • Electric components and printed circuit boards are disposed of as electronic scrap. •...
Technical Specifications Permissible Operating and Storage Conditions Temperature range for operation • -25 … +50 °C according to ISO 7176-9: Temperature range for storage • -40 … +65 °C according to ISO 7176-9: Electrical system Motors • 2 x 340 W Batteries •...
Page 120
Driving characteristics Max. climbable obstacle height • 7.5 cm Turning radius • 56 cm Drive range in accordance with • 58 km ISO 7176 *** Dimensions Standard Contour Flex Total height • 94 cm • 105 cm • 98 cm Drive unit width •...
Page 121
Dimensions Standard Contour Flex Backrest angle • -10°, 0°, +7.5°, • -10°...+45° • -10°...+45° +15°, +22.5°, (electr.) +30° Armrest height • 25-35 / 29-39 cm • 25-35 / 29-39 cm • 25-35 / 29-39 cm Legrest lengths • Short (for leg length 32-38 cm) • 29.5 - 35.5 cm •...
Page 122
*** Note: The drive range of an electric wheelchair is strongly influenced by external factors, such as the charging state of the batteries, surrounding temperature, local topography, road surface characteristics, tyre pressure, weight of driver, drive style and use of batteries for lighting, servos etc.
It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed. The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare®. Delivery Inspection...