Table of Contents
Advertisement
R
10
Maintaining & Servicing Your Appliance
CAUTION
Shock hazard
.
• Unplug appliiance before servicing
or maintaining appliance
A. General Maintenance
1. Types of Fuel
Depending on the type of fuel you are burning will dictate how
often you have to clean your firepot. If the fuel you are burning
has a high dirt or ash content or you are burning shelled field
corn, it may be necessary to clean the firepot more than once
a day. Dirty fuel will cause clinkers to form in the firepot. A
clinker is formed when dirt, ash or a non-burnable substance
is heated to 2000°F (1093°C) and becomes glass-like. See
"F" in this section for more details on fuels with high ash
content.
Figure 26.1 - Large Clinker
2. Cleaning Firepot with Cleaning Rod & Firepot
Scraper
•
Frequency: Daily or more often as needed
•
By: Homeowner
•
Task:
a. The appliance must be in complete shutdown and cool
and the exhaust blower off.
b. Pull firepot cleaning rod OUT a couple of times to help
shake debris loose. If rod is hard to pull, it may be
necessary to use your firepot scraper to chip away
material that has built up on the bottom plate of the
firepot and to push out any clinkers. Larger clinkers
may have to be removed from the top of the firepot.
Corn clinkers can be especially difficult to break up.
c. The firepot floor plate must be fully closed when
finished.
Fire Hazard.
• NEVER pull firepot cleaning rod or cleaning
slide plates out when appliance is operating.
Hot pellets may fall into ashpan and may start
a fire or you may experience mis-starts due to
lack of vacuum.
Page 28
Clinker
WARNING
3. Cleaning Ash Drawer
•
Frequency: As needed
•
By: Homeowner
•
Task:
Locate the ash drawer underneath the firepot. Slide
the ash drawer straight out and empty ashes into a
noncombustible container and re-install ash drawer.
See Disposal of Ashes on page 29.
4. Ash Removal from Firebox
•
Frequency: Weekly or as needed
•
By: Homeowner
•
Task:
a. There must not be any hot ashes in the firebox during
cleaning so allow the appliance to completely cool.
The firebox ash should be removed every time the
firepot is cleaned. Frequent cleaning of the ash in the
firebox will help slow down the build-up of ash in the
exhaust blower and vent system.
b. Plug in your appliance, if unplugged, and turn the
thermostat on and immediatley shut it off to start the
exhaust blower on its cycle time. It will pull fly ash out
the exhaust instead of into the room.
c. Open the front door. Directly underneath the firebox
door and to the left and right of the firepot are 2 cleaning
slide plates. Pull both slide plates out and then open
the glass door. Sweep the remaining ash from the
firebox into the 2 open holes. A paint brush works well
for this. Close slide plates.
d. This ash is deposited in the same ash drawer as the
firepot debris. The ash drawer should be emptied every
time you clean the firebox. Remember to place the ash
and debris into a metal or noncombustible container.
e. The 2 cleaning slide plates must be fully closed when
cleaning is complete. See Disposal of Ashes on page
29.
Fire Hazard.
• The cleaning slide plates must be fully
CLOSED when appliance is operating. Hot
pellets may fall into ashpan and start a fire.
Disposal of Ashes
• Ashes should be placed in metal container
• Ashes should be retained in closed container
7001-142C
Santa Fe Pellet Stove
WARNING
WARNING
with tight fitting lid.
until all cinders have thoroughly cooled.
November 2, 2005
Hide quick links:
Advertisement
Table of Contents
