Re-Assigning Device Keys; Using Keymover; Programming Keymover - One for All 6-Device Universal Remote User Manual

FAV (see "Using Channel Scan" on
page 10).
NOTE: Only channels of one mode can
be stored for Favorite Channel Scan.
1. On the remote control, press TV,
VCR, DVD or CBL/SAT once.
Press and hold SET until the LED
2.
(red light) blinks twice, then
release SET.
3. Enter 9 9 6. The LED will blink
twice.
4. Use the keypad to enter a
favorite channel number (e.g.,
031). Then press SET once.
NOTE: If the original remote control
required pressing an ENTER key to
change the channel, also press the
ENTER key after the channel number
(e.g., 0 3 1 ENTER).
5. If desired, repeat step 4 (in this
section) for each favorite
channel to be stored, up to a
total of 10 channels.
NOTE: If you try entering more than 10
channels, the remote control will
automatically exit programming.
6. To exit programming, press and
hold SET for 3 seconds. The LED
will blink twice.
RE-ASSIGNING DEVICE
KEYS
You can set the One For All 6L
Universal Remote Control (URC-6020
B00) to control a second TV, SAT,
DVD player, or other device. For
example, to control a TV, a cable box,
and two DVDs, you will need to re-
assign an unused device key (i.e.,
VCR) to operate the second DVD as
follows:
1. On the remote control, press and
hold SET until the LED (red
light) blinks twice, then release
SET.
2. Enter 9 9 2. The LED will blink
twice.
Press DVD once, then press VCR
3.
once.
4. The VCR key is now ready to be
programmed for your second
DVD. See "Setting Up Your
Components" on page 6.
To re-assign other device keys to the
VCR key, repeat steps 1 through 4 by
substituting the sequence from the
below chart:
To Re-Assign
Device
VCR as 2nd
TV key:
VCR as 2nd
CBL/SAT key:
VCR as 2nd
PVR key:
VCR as 2nd
AUD key:
You can also re-assign another
unused device key by substituting an
open key for the VCR key in the above
chart and performing the sequence.
For example, to re-assign an unused
CBL/SAT key as a 2nd TV key, perform
SET - 9 - 9 - 2 - TV -
CBL/SAT. When a re-assignment is
done, the LED (red light) will blink
twice to confirm your choice. At that
time, you will need to program the
remote control for the new device (see
"Setting Up Your Components" on
page 6).

USING KEYMOVER

The One For All 6L Universal Remote
Control (URC-6020 B00) includes a
Keymover feature that allows you to
map (or copy) keys from one mode
(i.e., source mode) to another mode
(i.e., destination mode).
NOTE: The following keys cannot be
used as a source or destination: TV,
CBL/SAT, VCR, DVD, PVR, AUD, FAV, and
SET.
P K
ROGRAMMING
For example, if your VCR does not
have volume control, you can map
those keys (i.e., VOL +, VOL -, and
MUTE) from the TV mode to the VCR
mode as follows:
1. Press and hold SET until the LED
(red light) blinks twice, then
release SET.
Enter 9 9 4. The LED will blink
2.
twice.
3. For the source mode, press TV
once.
4. For the source key, press VOL +
once.

Re-assigning Device Keys

O ' M
WNER S ANUAL
Perform Sequence
SET - 9 - 9 - 2 - TV -
VCR
SET - 9 - 9 - 2 -
CBL/SAT - VCR
SET - 9 - 9 - 2 - PVR -
VCR
SET - 9 - 9 - 2 - AUD -
VCR
EYMOVER
11