Skoda Roomster Owner's Manual page 164

›
Use the valve remover to unscrew the valve core and place it on a clean sur-
1
face (rag, paper, etc.).
Sealing and inflating tyres
ä
First read and observe the introductory information and safety warn-
ings on page 160.
Sealing
›
Forcefully shake the tyre inflator bottle
›
Firmly screw the inflation hose
3
direction. The film on the cap is pierced automatically.
›
Remove the plug from the inflation hose
the tyre valve.
›
Hold the bottle with the bottom facing upwards and fill all of the sealing
10
agent from the tyre inflator bottle into the tyre.
›
Remove the empty tyre inflator bottle from the valve.
›
Screw the valve core back into the tyre valve using the valve remover
Inflating
›
Screw the tyre inflation hose
5
firmly onto the tyre valve.
›
Check that the air release valve
›
Start the engine and run it in idle.
›
Plug the connector into 12 Volt socket
9
›
Switch on the air compressor with the ON and OFF switch
›
Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved.
Maximum run time of 8 minutes »
›
Switch off the air compressor.
›
If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation
hose from the tyre valve.
5
›
Drive the vehicle 10 metres forwards or backwards to allow the sealing agent to
"distribute" in the tyre.
›
Firmly screw the tyre inflation hose
inflation process.
›
If you cannot reach the required tyre inflation pressure here either, this means
the tyre has sustained too much damage. You cannot seal with tyre with the
breakdown kit » .
›
Switch off the air compressor.
›
Remove the tyre inflation hose
5
Once a tyre inflation pressure of 2.0 – 2.5 bar is achieved, continue the journey at
a maximum speed of 80 km/h (50 mph).
162
Do-it-yourself
» Fig. 134 on page 161 several times.
10
onto the tyre inflator bottle in a clockwise
10
and plug the open end fully onto
3
» Fig. 134 on page 161 of the air compressor
is closed.
7
» page 61, 12-volt power socket.
8 .
!
back onto the tyre valve and repeat the
5
from the tyre valve.
Check the tyre inflation pressure after driving for 10 minutes
Ð
WARNING
During inflation, the tyre inflation hose and air compressor may get hot- risk
■
of injury!
Do not place the hot tyre inflation hose or hot air compressor on flammable
■
materials - risk of fire!
If you cannot inflate the tyre to at least 2.0 bar, this means the damage sus-
■
tained was too serious. The sealing agent cannot be used to seal the tyre. Do
not drive the vehicle. Get professional assistance!
CAUTION
Switch off the air compressor after running 8 minutes at the latest - danger of
overheating! Allow the air compressor to cool a few minutes before switching it
on again.
.
1
Check after driving for 10 minutes
ä
First read and observe the introductory information and safety warn-
ings on page 160.
Check the tyre inflation pressure after driving for 10 minutes!
If the tyre inflation pressure is 1.3 bar or less:
›
Do not drive the vehicle! You cannot properly seal with tyre with the break-

down kit.
›
Get professional assistance.
If the tyre inflation pressure is 1.3 bar or more:
›
Adjust the tyre inflation pressure to the correct value (see inside of fuel filler
cap).
›
Continue driving carefully to the nearest ŠKODA specialist garage at a maxi-
mum speed of 80 km/h (50 mph).
» page 162.
Ð
Ð