Basic Saw Cuts; Maintenance - DeWalt DW744XP-XE Instruction Manual

BASIC SAW CUTS

Ripping (fig. A1, A2, M1, M2)
WARNING: Sharp edges.
1. Set the blade to 0°.
2. Lock the rip fence (7) (fig. A1).
3. Raise the blade until it is about 3.2 mm higher than the top of the
workpiece.
4. Hold the workpiece flat on the table and against the fence. Keep the
workpiece approx. 25 mm away from the blade.
WARNING: Keep both hands away from the path of the blade
(fig. M2).
5. Press the green button to switch ON and allow the blade to reach full
speed.
6. Slowly feed the workpiece underneath the guard, keeping it firmly
pressed against the rip fence. Allow the teeth to cut, and do not force
the workpiece through the blade. The blade speed should be kept
constant.
7. Always use a push stick (43) when close to the blade (fig. M1).
8. After completing the cut, switch the saw OFF, allow the blade to
stopand remove the workpiece.
WARNING:
• Never push or hold the "free" or cut-off-side of the
workpiece.
• Do not cut excessively small workpieces.
• Always use a push stick when ripping small workpieces.
Bevel Cuts
1. Set the required bevel angle (refer to the section "Adjusting the rip
scale").
2. Proceed as for ripping.
Cross-cutting and Bevel Cross-cutting
1. Remove the rip fence and install the mitre gauge in the desired slot.
2. Lock the mitre gauge at 0°.
3. Proceed as for ripping.
Mitre Cuts (fig. A1)
1. Set the mitre gauge to the required angle.
2. Always hold the workpiece tightly against the face of the mitre gauge.
3. Proceed as for ripping.
Compound Mitre
This cut is a combination of a mitre and a bevel cut.
1. Set the bevel to the angle required.
2. Proceed as for a cross-cut mitre.
Support for Long Pieces
Always support long pieces.
Support long workpieces using any convenient means such as saw-
horses or similar devices to keep the ends from dropping.
Dust Extraction (fig. A2)
The machine is provided with dust extraction outlets (5, 14). An adaptor is
provided for outlet (14) .
M1
M2
N
O
7
WARNING:
• Connect a suitable dust extraction device during all sawing
operations.
• Whenever possible, connect a dust extraction device
designed in accordance with the relevant regulations
regarding dust emission.
Transporting (fig. A1)
• Always carry the machine at the hand indentations.
WARNING: Always transport the machine with the upper blade
guard fitted.

MAINTENANCE

Your D WALT machine has been designed to operate over a long period of
E
time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication (fig. N)
The motor and bearings require no additional lubrication. If raising
and lowering the blade becomes difficult, clean and grease the height
adjustment screws:
1. Turn the saw on its side.
2. Clean and grease the height adjustment threads as shown in figure N.
Use general purpose grease.
Cleaning
WARNING: To reduce the risk of serious personal injury, turn unit
off and disconnect machine from power source before cleaning. An
accidental start-up can cause injury.
To maintain correct operation of your saw, clean the table insert area
regularly. Remove saw dust, chips and any other debris. If using
compressed air, always wear approved eye protection.
Regularly clean the dust collection system:
1. Turn the saw on its side.
2. Remove the screws (44) (fig. O).
3. Remove all dust and resecure the access door (45) using the screws
(fig. O).
IMPORTANT: The guard and throat plate must be placed in position before
operating the saw.
Accessories
WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
E
accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT, recommended accessories should
E
be used with this product.
Recommended accessories for use with your tool are available at extra
cost from your local service center. If you need any assistance in locating
any accessory, please contact D WALT Industrial Tool Co., 20 Fletcher
E
Road, Mooroolbark, VIC 3138 Australia or call 1800 654 155 or (NZ)
0800 339258.
The following attachments are available:
– legstand DE7440
WARNING: Sharp edges.