Safety Instructions - DeWalt DW744XP-XE Instruction Manual

Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the manual and pay
attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not
avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
(Aust) or 0800 339258 (NZ).

SAFETY INSTRUCTIONS

When using power tools, always observe the safety regulationsapplicable in your country to reduce the risk of fire,
electric shockand personal injury. Read the following safety instructions beforeattempting to operate this product.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE!
General
1. Keep work area clean .
Cluttered areas and benches can cause accidents.
2. Consider work area environment .
Do not expose power tools to humidity. Keep work area well lit. Do not use power tools in the presence of
flammable liquids or gases.
3. Guard against electric shock .
Prevent body contact with earthed surfaces (e.g., pipes, radiators, cookers and refrigerators). For use under
extreme conditions (e.g., high humidity, when metal swarf is being produced, etc.) electric safety can be
improved by inserting an isolating transformer or a (FI) earth-leakage circuit-breaker.
4. Keep children away .
Do not let children come into contact with the tool or extension cord. Supervision is required for inexperienced
operators.
5. Extension cords for outdoor use .
When the tool is used outdoors, always use extension cords intended for outdoor use and marked
accordingly.
6. Store idle tools .
When not in use, power tools must be stored in a dry place and locked up securely, out of reach of children.
7. Dress properly.
Do not wear loose clothing or jewellery. They can be caught in moving parts. Preferably wear rubber gloves
and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way.
8. Wear safety goggles .
Also use a face or dust mask in case the operations produce dust or flying particles.
9. Beware of maximum sound pressure .
Take appropriate measures for the protection of hearing if the sound pressure of 85 dB(A) is exceeded.
10. Secure workpiece .
Keep proper footing and balance at all times .
11. Do not overreach .
Always check that adjusting keys and wrenches are removed from the tool before operating the tool.
12. Avoid unintentional starting .
Do not carry the plugged-in tool with a finger on the switch. Be sure that the switch is released when
plugging in.
13. Stay alert .
Watch what you are doing. Use common sense. Do not operate the tool when you are tired.
WALT TOOL, CALL US AT: 1800 654 155
E
2
14. Disconnect tool .
Shut off power and wait for the tool to come to a complete standstill before leaving it unattended. Unplug the
tool when not in use, before servicing or changing accessories.
15. Remove adjusting keys and wrenches .
Always check that adjusting keys and wrenches are removed from the tool before operating the tool.
16. Use appropriate tool .
The intended use is described in this instruction manual. Do not force small tools or attachments to do the job
of a heavy-duty tool. The tool will do the job better and safer at the rate for which it was intended.
WARNING! The use of any accessory or attachment or performance of any operation with this tool, other than
those recommended in this instruction manual may present a risk of personal injury.
17. Do not abuse cord.
Never carry the tool by its cord or pull it to disconnect from the socket. Keep the cord away from heat, oil and
sharp edges.
18. Maintain tools with care.
Keep the tools in good condition and clean for better and safer performance. Follow the instructions for
maintenance and changing accessories. Inspect the tool cords at regular intervals and, if damaged, have them
repaired by an authorized D WALT repair agent. Inspect the extension cords periodically and replace them if
E
damaged. Keep all controls dry, clean and free from oil and grease.
19. Check for damaged parts .
Before using the tool, carefully check it for damage to ensure that it will operate properly and perform its
intended function. Check for misalignment and seizure of moving parts, breakage of parts and any other
conditions that may affect its operation. Have damaged guards or other defective parts repaired or replaced as
instructed. Do not use the tool if the switch is defective. Have the switch replaced by an authorized D
repair agent.
20. Have your tool repaired by an authorized D
This power tool is in accordance with the relevant safety regulations. To avoid danger, electric appliances
must only be repaired by qualified technicians.
Additional Safety Rules for Saw Benches
• Do - protect the electrical supply line with a suitable fuse or circuit breaker.
• Do - make certain the blade rotates in the correct direction and that the teeth are pointing to the front of the
saw bench.
• Do - be sure all clamp handles are tight before starting any operation.
• Do - be sure all blade and arbor collars are clean and the recessed sides of the collars are against the blade.
• Do - keep the saw blade sharp and properly set.
• Do - keep hands out of the path of the saw blade.
• Do - shut off the power and wait for the saw blade to stop before servicing or adjusting the tool.
• Do - disconnect the saw from the mains supply before changing the blade or carrying out maintenance.
• Don't - attempt to operate on anything other than the designated voltage.
• Don't - use blades larger or smaller than those which are recommended.
• Don't - force the cutting action. (Stalling or partial stalling of the motor can cause major damage. Allow the
motor to reach full speed before cutting.)
• Don't - cut ferrous metals, non-ferrous metals or masonry.
• Don't - use abrasive wheels.
• Don't - apply lubricants to the blade when it is running.
• Don't - place either hand in the blade area when the saw is connected to the power source.
• Don't - use any blades other than those specified in this instruction manual.
• Don't - operate the saw without the guards in place.
• Don't - reach around behind the saw blade.
• Don't - place hands closer than 150 mm from the saw blade while cutting.
• Don't - use damaged or cracked saw blades.
Residual Risks
The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
WALT repair agent .
E
WALT
E