Table of Contents
Advertisement
For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: _______________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
41923-01 • 11/21/05
Advertisement
Table of Contents
Related Manuals for Hunter 41923
Summary of Contents for Hunter 41923
- Page 1 For Your Records and Warranty Assistance Model Name: _____________________ Catalog/Model No.: ________________ Serial No.: _______________________ Date Purchased: ___________________ Where Purchased: _________________ For reference also attach your receipt or a copy of your receipt to the manual. 41923-01 • 11/21/05...
-
Page 2: Table Of Contents
• Read this entire manual carefully before beginning installation. Save these instructions. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied. - Page 3 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation fl exibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profi le, Standard, or Angle mounting. e steps in this manual include instructions for all three Installer’s Choice mounting methods.
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Ceiling Plate
e pilot holes should be 9/64” in diameter. 2-2. Your fan comes with four neoprene noise isolators (“Isolators”). Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate. -
Page 6: Assembling And Hanging The Fan
(steps 3-3 – 3-5). Note: For low profile mounting, the downrod is replaced with the low profile washer. 3-1. To assemble fan to hang down from a flat or angled ceiling, insert the downrod through the canopy and canopy trim ring. Feed the wires from the fan through the downrod. -
Page 7: Setting The Remote Transmitter And Reciever
CAUTION: e remote control device complies with part 15 of the FCC rules. Changes or modifi cations not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Operation is subject to the following two conditions: 1. -
Page 8: Wiring The Fan
• e black/white wire from the fan to the red wire from the receiver (marked on white tag “LIGHT OUT”) • e black wire from the fan to the black wire from the receiver (marked on white tag “FAN OUT”) •... -
Page 9: Installing The Canopy And Canopy Trim Ring
6-1. Holding the canopy, raise the fan off the hook. 6-2. Align the slots in the canopy with the tabs on the ceiling plate. 6-3. Raise the canopy over the ceiling plate. Rotate the canopy clockwise until the tabs on the ceiling plate totally engage with the slots in the canopy. -
Page 10: Assembling The Blades
Blade Mounting Screw Hunter Fan Company Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 7-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. -
Page 11: Installing The Switch Housing
Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three housing assembly screws. Note: You can customize your Hunter fan with a number of accessory light kits. 41923-01 • 11/21/05 8 •... -
Page 12: Operating The Remote Control And Mounting The Holder
Step 9-5 Hunter Fan Company 9-1. e remote transmitter has individual buttons for turning the fan off and on and controlling the light and fan speed. 9-2. For best operation, start the fan by pressing high, then select Fan Speed your desired speed. -
Page 13: Operating And Cleaning Your Ceiling Fan
10-2. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a direct breeze. In cold weather, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at the ceiling around the room without causing a draft. -
Page 14: Troubleshooting
6. If the transmitter LED light does not come on, replace the battery with a new 12-volt alkaline battery. If the LED light does come on but the fan will not work, check the settings in the receiver and transmitter. Refer to 4• Setting the Remote Transmitter and Receiver 7 for more information.