Page 2
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.
About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 1017C-TF. In- stallation and maintenance should be performed by experienced technicians only. The SuperServer 1017C-TF is a high-end server based on the SC111LT-330CB 1U rackmount chassis and the Super X9SCL-F single processor serverboard.
Page 4
UPER ERVER 1017C-TF User's Manual Chapter 4: System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 1017C-TF. Chapter 5: Advanced Serverboard Setup Chapter 5 provides detailed information on the X9SCL-F serverboard, including the locations and functions of connections, headers and jumpers.
UPER ERVER 1017C-TF User's Manual Table of Contents Chapter 1 Introduction Overview ......................1-1 Motherboard Features ..................1-2 Processors ...................... 1-2 Memory ......................1-2 Serial ATA ......................1-2 I/O Ports ......................1-2 Graphics Controller ..................1-2 Server Chassis Features ................1-3 System Power ....................
Page 7
Table of Contents Chapter 3 System Interface Overview ......................3-1 Control Panel Buttons ..................3-1 Reset ....................... 3-1 Power ......................3-1 UID ........................3-1 Control Panel LEDs ..................3-2 Universal Information LED ................3-2 NIC2 ........................ 3-3 NIC1 ........................ 3-3 HDD .........................
Page 8
UPER ERVER 1017C-TF User's Manual 5-12 Installing Drivers .................... 5-23 Supero Doctor III ................... 5-24 Chapter 6 Advanced Chassis Setup Static-Sensitive Devices .................. 6-1 Precautions ..................... 6-1 Control Panel ....................6-2 System Cooling ....................6-2 System Fan Failure ..................6-3 Installing the Air Shroud ..................
Chapter 1 Introduction Overview The SuperServer 1017C-TF is a high-end server comprised of two main subsys- tems: the SC111LT-330CB 1U server chassis and the X9SCL-F single processor motherboard. Please refer to our web site for information on operating systems that have been certifi...
ERVER 1017C-TF User's Manual Motherboard Features At the heart of the SuperServer 1017C-TF lies the X9SCL-F, a single processor motherboard based on Intel's C202 chipset. Below are the main features of the X9SCL-F (see Figure 1-1 for a block diagram of the chipset).
Chapter 1: Introduction Server Chassis Features The SC111LT-330CB chassis features four 2.5" hard drive bays and a high-effi ciency power supply. Details on the chassis and on service procedures can be found in Chapter 6. The following is a general outline of the main features of the chassis. System Power The SC111LT-330CB features a single 330W power supply module.
Page 12
UPER ERVER 1017C-TF User's Manual Figure 1-1. Intel C202 Chipset: System Block Diagram Note: This is a general block diagram. Please see Chapter 5 for details.
Chapter 1: Introduction Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel:...
Preparing for Setup The box the SuperServer 1017C-TF was shipped in should include two sets of rail assemblies, two rail mounting brackets and the mounting screws you will need to install the system into the rack. Follow the steps in the order given to complete the installation process in a minimum amount of time.
UPER ERVER 1017C-TF User's Manual installation only in a Restricted Access Location (dedicated equipment rooms, service closets and the like). • This product is not suitable for use with visual display work place devices acccording to §2 of the the German Ordinance for Work with Visual Display Units.
Chapter 2: Server Installation Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating tempera- ture of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient tempera- ture (Tmra).
UPER ERVER 1017C-TF User's Manual Installing the System into a Rack This section provides information on installing the SC111 chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly.
Chapter 2: Server Installation Figure 2-2. Installing the Inner Rails Installing the Inner Rails Installing the Inner Rails to the Chassis Place the inner rail on the side of the chassis, aligning the hooks of the chas- sis with the rail extension holes. Make sure the rail faces "outward". Slide the rail toward the front of the chassis.
UPER ERVER 1017C-TF User's Manual Rear Outer Rail Secure this end to the rear of the rack Attach this end to the rear of the Front outer rail Attach this end to the front of the outer rail Secure this end...
Chapter 2: Server Installation SCALE 0.500 Figure 2-4. Installing the to the Rack Installing the Chassis into the Rack Installing the Chassis Confi rm that the inner rails are correctly installed on the chassis, then confi rm that the outer rails are correctly installed on the rack. Align the inner rails on the chassis with the front of the outer rails on the rack.
ERVER 1017C-TF User's Manual Checking the Serverboard Setup After you install the 1017C-TF in the rack, you will need to open the unit to make sure the serverboard is properly installed and all the connections have been made. Removing the Chassis Cover (Figure 2-5) Grasp the two handles on either side and pull the unit straight out until it locks (you will hear a "click").
Chapter 2: Server Installation Your server system may have come with system memory already installed. Make sure all DIMMs are fully seated in their slots. For details on adding system memory, refer to Chapter 5. If desired, you can install add-on cards to the system. See Chapter 5 for details on installing PCI add-on cards.
Chapter 3: System Interface Chapter 3 System Interface Overview There are several LEDs on the control panel to keep you constantly informed of the overall status of the system as well as the three buttons described below. Control Panel Buttons There are three buttons located on the front of the chassis: a reset button, a power on/off button and a UID button.
UPER ERVER 1017C-TF User's Manual Control Panel LEDs The control panel located on the front of the SC111LT chassis has fi ve LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take.
Chapter 3: System Interface NIC2 Indicates network activity on LAN2 when fl ashing. NIC1 Indicates network activity on LAN1 when fl ashing. Indicates DVD-ROM/hard drive activity when fl ashing. Power Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating.
UPER ERVER 1017C-TF User's Manual Hard Drive Carrier LEDs Each hard drive carrier has two LEDs. • Green: When illuminated, the green LED on the front of the drive carrier in- dicates drive activity. A connection to the SATA backplane enables this LED to blink on and off when that particular drive is being accessed.
System Safety Electrical Safety Precautions Basic electrical safety precautions should be followed to protect yourself from harm and the SuperServer 1017C-TF from damage: • Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet.
Keep the area around the system clean and free of clutter. • The 1017C-TF weighs approximately 37 lbs (16.8 kg) when fully loaded. When lifting the system, two people at either end should lift slowly with their feet spread out to distribute the weight. Always keep your back straight and lift with your legs.
Chapter 4: System Safety • After accessing the inside of the system, close the system back up and secure it to the rack unit after ensuring that all connections have been made. ESD Precautions Electrostatic Discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other.
ERVER 1017C-TF User's Manual Operating Precautions Care must be taken to assure that the chassis cover is in place when the 1017C-TF is operating to assure proper cooling. Out of warranty damage to the system can occur if this practice is not strictly followed.
Chapter 5: Advanced Motherboard Setup Chapter 5 Advanced Motherboard Setup This chapter covers the steps required to install processors and heatsinks to the X9SCL-F motherboard, connect the data and power cables and install add-on cards. All motherboard jumpers and connections are described and a layout and quick reference chart are included in this chapter.
UPER ERVER 1017C-TF User's Manual Processor and Heatsink Installation Notes: • Always connect the power cord last and always remove it before adding, re- moving or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the CPU heatsink.
Page 35
Chapter 5: Advanced Motherboard Setup Use your thumb and your index fi nger to hold the CPU at the top center edge and the bottom center edge of the CPU. Align the CPU key (the semi-circle cutouts) against the socket keys. Once aligned, carefully lower the CPU straight down to the socket.
UPER ERVER 1017C-TF User's Manual CPU properly installed Load lever locked into place. Warning: The CPU will only seat inside the socket in one direction. Make sure it is properly inserted before closing the load plate. If it doesn't close properly, do not force it as it may damage your CPU.
Page 37
Chapter 5: Advanced Motherboard Setup Figure 5-3. Installing the Heatsink Once the CPU is loose, remove the it from the CPU socket. Clean the surface of the CPU and the heatsink, removing the used thermal grease. Reapply the proper amount of thermal grease on the surface before re-installing the CPU and the heatsink.
UPER ERVER 1017C-TF User's Manual Connecting Cables Now that the processors are installed, the next step is to connect the cables to the motherboard. These include the data (ribbon) cables for the peripherals and control panel and the power cables.
Chapter 5: Advanced Motherboard Setup All JF1 wires have been bundled into single keyed ribbon cable to simplify their con- nection. Connect one end of this cable to JF1 and the other end to the Control Panel printed circuit board, located just behind the system status LEDs in the chassis. See the Connector Defi...
UPER ERVER 1017C-TF User's Manual Installing Memory Note: Check the Supermicro web site for recommended memory modules. CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. Installing DIMMs Insert the desired number of DIMMs into the memory slots, starting with slots DIMM1A.
Page 41
Chapter 5: Advanced Motherboard Setup Figure 5-3. Installing DIMM into Slot Notch Notch To Install: Insert module vertically and press down until it snaps into place. Pay attention to the alignment notch at Front View the bottom. To Remove: Note: Notch should align Use your thumbs to with the receptive key gently push the release...
UPER ERVER 1017C-TF User's Manual Adding PCI Cards PCI Expansion Slots One riser card is used to support a PCI expansion (add-on) card in the system. The SC111LT-330CB chassis can accommodate one standard size (full height full length) PCI expansion card. When viewed from the chassis front, the card installs to the left rear of the system.
Page 44
UPER ERVER 1017C-TF User's Manual Headers/Connectors Number Connector Description Onboard Battery 4,16 COM1/COM2 COM1/2 Serial Port/Header BIOS SPI BIOS 42,38,37,7,30 Fans 1~4, Fan A System/CPU Fan Headers SPI Programming (internal use) Front Panel Control Header Chassis Intrusion Header JLED1 Power LED Indicator Header...
Chapter 5: Advanced Motherboard Setup Connector Defi nitions ATX Power 24-pin Connector Pin Defi nitions (JPW1) Pin# Defi nition Pin # Defi nition ATX Power Connector +3.3V +3.3V A 24-pin main power connector is located -12V +3.3V at JPW1. This power connector meet the SSI EPS 12V specifi...
Page 46
UPER ERVER 1017C-TF User's Manual NIC1/NIC2 (LAN1/LAN2) The NIC (Network Interface Controller) LED connection for LAN port 1 is located LAN1/LAN2 LED on pins 11 and 12 of JF1, and the LED Pin Defi nitions (JF1) connection for LAN Port 2 is on Pins 9 Pin# Defi...
Page 47
Chapter 5: Advanced Motherboard Setup Back Panel USB0/1 Pin Defi nitions Universal Serial Bus (USB) Pin# Defi nition Pin# Defi nition Two Universal Serial Bus ports (USB 0/1) are located on the I/O backpanel and an USB_PN1 USB_PN0 additional six USB ports in three head- USB_PP1 USB_PP0 ers, USB2/3, 4/5, 12/13 provide front/...
Page 48
UPER ERVER 1017C-TF User's Manual Fan Headers The X9SCL-F has fi ve fan headers (Fan1 ~ Fan4 and FanA). These are all 4-pin fan headers, however pins 1-3 are backward Fan Header compatible with traditional 3-pin fans. Pin Defi nitions...
Page 49
Chapter 5: Advanced Motherboard Setup Trusted Platform Module Header Trusted Platform Module Header Pin Defi nitions This header is used to connect a Trusted Pin # Defi nition Pin # Defi nition Platform Module (TPM), available sepa- LCLK rately from a third-party vendor. A TPM is LFRAME No Pin a security device that allows encryption...
Page 50
UPER ERVER 1017C-TF User's Manual T-SGPIO 0/1 Headers Serial_Link-SGPIO Pin Defi nitions Two T-SGPIO (Serial-Link General Pur- Pin# Defi nition Defi nition pose Input/Output) headers are located near the SATA connectors on the moth- Ground DATA Out erboard. These headers are used to com-...
Chapter 5: Advanced Motherboard Setup Jumper Settings Explanation of Jumpers To modify the operation of the mother- board, jumpers can be used to choose Connector between optional settings. Jumpers cre- Pins ate shorts between two pins to change the function of the connector. Pin 1 is Jumper identifi...
Page 52
UPER ERVER 1017C-TF User's Manual PCI Slot SMB Enable PCI Slot SMB Enable/Disable Jumper Settings Use Jumpers JI C1/JI C2 to enable PCI Jumper Setting Defi nition SMB (System Management Bus) support Closed Enabled to improve system management for the...
Chapter 5: Advanced Motherboard Setup 5-10 Onboard Indicators LAN1/LAN2 LEDs LAN LED The Ethernet ports (located beside the Connection Speed Indicator VGA port) have two LEDs. On each Giga- LED State Defi nition bit LAN port, the yellow LED indicates No connection or 10 Mb/s activity when blinking while the other LED Green...
UPER ERVER 1017C-TF User's Manual 5-11 SATA Drive Connections SATA Port Pin Defi nitions (SATA0 ~ SATA5) Pin # Defi nition SATA Ports Ground Six Serial ATA (SATA) ports (I-SATA 0~5) are located on the motherboard. See the table on the right for pin defi nitions for the Ground onboard SATA ports.
Chapter 5: Advanced Motherboard Setup 5-12 Installing Drivers After all the hardware and operating system have been installed, you need to install certain drivers. The necessary drivers are all included on the Supermicro CD that came packaged with your motherboard. After inserting this CD into your CD-ROM drive, the display shown in Figure 5-4 should appear.
ERVER 1017C-TF User's Manual Supero Doctor III The Supero Doctor III program is a Web base management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client. The Supero Doctor III program included on the CDROM that came with your serverboard allows you to monitor the environment and operations of your system.
Page 57
Chapter 5: Advanced Motherboard Setup Supero Doctor III Interface Display Screen (Remote Control) Note: SD III Software Revision 1.0 can be downloaded from our Web Site at: ftp:// ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's Guide at: http://www.supermicro.com/manuals/other/SDIII_User_Guide.pdf. For Linux, we will still recommend Supero Doctor II.
Chapter 6: Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform main- tenance on the SC111 chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered. If some steps are unnecessary, skip ahead to the next step.
UPER ERVER 1017C-TF Manual Figure 6-1. Chassis: Front and Rear Views Front USB Ports (optional) Control Panel Hot-Swap Drive Bays (4) Dedicated IPMI LAN Power Supply Mouse/Kybrd VGA Port PCI Slots USB Ports COM Port LAN Ports UID Button Control Panel The control panel (located on the front of the chassis) must be connected to the JF1 connector on the serverboard to provide you with system status indications.
Chapter 6: Advanced Chassis Setup Adding a System Fan Turn off the power to the system and unplug the AC power cord. Remove the chassis cover then remove the dummy fan from the fan tray. Place the new fan into the vacant space in the housing while making sure the arrows on the top of the fan (indicating air direction) point in the same direc- tion as the arrows on the other fans.
Page 62
UPER ERVER 1017C-TF Manual Figure 6-2: System Fans (shown with optional fans installed) Figure 6-3. Air Shroud Installation...
Proceed to the "DVD-ROM Drive Installation" section later in this chapter for instructions. Note: Only a "slim" DVD-ROM drive will fi t into the 1017C-TF. Hard Drive Installation The hard drives are mounted in drive carriers to simplify their installation and removal from the chassis.
Page 64
UPER ERVER 1017C-TF Manual Insert a drive into the carrier with the PCB side facing down and the connec- tor end toward the rear of the carrier. Align the drive in the carrier so that the screw holes of both line up. Note that there are holes in the carrier marked "SAS"...
Figure 6-5. Removing a Hard Drive DVD Drive Installation The 1017C-TF server includes a pre-installed DVD-ROM. Installing or Replacing a DVD-ROM Drive (Figure 6-6) Power down the system and if necessary, remove the server from the rack.
Page 66
UPER ERVER 1017C-TF Manual The DVD-ROM requires an additional lock screw (C) at the back of the DVD- ROM drive to be removed. Remove the lock screw through the interior of the chassis and gently push the DVD-ROM drive (D), DVD-ROM adapter card (E) and drive tray out through the front of the chassis.
Chapter 6: Advanced Chassis Setup Power Supply The SuperServer 1017C-TF has a single 330 watt power supply, which is auto- switching capable. This enables it to automatically sense and operate with a 100v - 240v input voltage. If the power supply module fails, the system will shut down and you will need to replace the module.
Chapter 7: BIOS Chapter 7 BIOS Introduction This chapter describes the AMI BIOS Setup Utility for the X9SCL-F. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter de- scribes the basic navigation of the AMI BIOS Setup Utility setup screens. Note: For instructions on BIOS recovery, please refer to the instruction guide posted at http://www.supermicro.com/support/manuals/.
UPER ERVER 1017C-TF User's Manual How to Start the Setup Utility Normally, the only visible Power-On Self-Test (POST) routine is the memory test. As the memory is being tested, press the <Delete> key to enter the main menu of the AMI BIOS Setup Utility. From the main menu, you can access the other setup screens.
Page 71
Chapter 7: BIOS System Overview: The following BIOS information will be displayed: System Time/System Date Use this option to change the system time and date. Highlight System Time or Sys- tem Date using the arrow keys. Enter new values through the keyboard. Press the <Tab>...
UPER ERVER 1017C-TF User's Manual Advanced Setup Confi gurations Use the arrow keys to select Boot Setup and hit <Enter> to access the submenu items: BIOS SETUP UTILTY Main Advanced Event Logs IPMI Boot Security Exit System Boot Feature Boot Feature Setting.
Page 73
Chapter 7: BIOS 19 at boot and allow the drives that are attached to these host adaptors to function as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap- tors will not capture Interrupt 19, and the drives attached to these adaptors will not function as bootable devices.
Page 74
UPER ERVER 1017C-TF User's Manual Adjacent Cache Line Prefetch (Available when supported by the CPU) The CPU fetches the cache line for 64 bytes if this option is set to Disabled. The CPU fetches both cache lines for 128 bytes as comprised if Enabled.
Page 75
Chapter 7: BIOS P-STATE Coordination This feature selects the type of coordination for the P-State of the processor. P-State is a processor operational state that reduces the processor's voltage and frequency. This makes the processor more energy effi icient, resulting in further gains.
Page 76
UPER ERVER 1017C-TF User's Manual North Bridge Confi guration This item displays the current North Bridge Revision. VT-d Select Enabled to enable Intel's Virtualization Technology support for Direct I/O VT-d by reporting the I/O device assignments to VMM through the DMAR ACPI Tables. This feature offers fully-protected I/O resource- sharing across the Intel platforms, providing the user with greater reliabil- ity, security and availability in networking and data-sharing.
Page 77
Chapter 7: BIOS Wake on LAN from S5 Select Enabled to enable the capabiltiy to 'wake-up' the system from the S5 power state (Soft Off State) through the Ethernet controller. The set- tings are Enabled and Disabled. Legacy USB Support This feature enables support for legacy USB devices.
Page 78
UPER ERVER 1017C-TF User's Manual Aggressive Link Power Management This feature Enables or Disables Agressive Link Power Management support for Cougar Point B0 stepping and later. The options are Enabled and Disabled. SATA Port0~Port5 This item displays the information detected on the installed SATA drives on the particular SATA port.
Page 79
Chapter 7: BIOS PCI Latency Timer This feature sets the latency Timer of each PCI device installed on a PCI bus. Select 64 to set the PCI latency to 64 PCI clock cycles. The options are 32, 64, 96, 128, 160, 192, 224 and 248.
Page 80
UPER ERVER 1017C-TF User's Manual Serial Port 2 Mode Use this feature to confi gure Serial Port 2 mode. The options are Normal, IrDA and ASK IR. IrDA (Infrared Data) is an industry standard for remote control devices. ASK IR (Amplitude Shifted Keying Infrared) is a protocol compatible with Sharp® branded PDAs and other infrared devices.
Page 81
Chapter 7: BIOS Parity: None, Even, Odd, Mark, or Space Stop Bits: 1 or 2 Hardware Health Confi guration Fan Speed Control Mode This feature allows the user to decide how the system controls the speeds of the onboard fans. The CPU temperature and the fan speed are correlative. When the CPU on-die temperature increases, the fan speed will also increase for effective system cooling.
Page 82
UPER ERVER 1017C-TF User's Manual High – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Temperature Tolerance’ has been reached (or has been exceeded) and may activate an overheat alarm: The information provided above is for your reference only. For more information on thermal management, please refer to Intel’s Web site at www.Intel.com.
UPER ERVER 1017C-TF User's Manual IPMI Confi guration (X9SCL-F/X9SCM-F Only) Intelligent Platform Management Interface (IPMI) is a set of common interfaces that IT administrators can use to monitor system health and to manage the system as a whole. For more information on the IPMI specifi cations, please visit Intel's website at www.intel.com.
Page 85
Chapter 7: BIOS SEL Components - Change this item to enable or disable all features of System Event Logging. The options are Enabled and Disabled. When Enabled, the following can be confi gured: Erase SEL - This option erases all logged SEL events. The options are No, Yes, On Next reset and Yes, On Every reset.
Chapter 7: BIOS Security Settings BIOS SETUP UTILTY Main Advanced Event Logs IPMI Boot Security Exit Password Description Set Setup Administrator Pasword. If ONLY the administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
UPER ERVER 1017C-TF User's Manual Exit Options BIOS SETUP UTILTY Main Advanced Event Logs IPMI Boot Security Exit Save Changes and Exit Exit system setup after Discard Changes and Exit saving the changes. Discard Changes Restore Defaults Save as User Defaults...
Page 89
Chapter 7: BIOS Save As User Defaults To set this feature, select Save as User Defaults from the Exit menu and press <En- ter>. This enables the user to save any changes to the BIOS setup for future use Restore User Defaults To set this feature, select Restore User Defaults from the Exit menu and press <En- ter>.
Appendix A: POST Error Beep Codes Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue with bootup.
Appendix B: System Specifi cations Appendix B System Specifi cations Processor ® ® Single Intel Xeon E3-1200 Series processor or a Core i3-2100 Series processor in an LGA1155 socket Note: Please refer to our web site for a complete listing of supported processors. Chipset Intel C202 BIOS...
Page 94
UPER ERVER 1017C-TF User's Manual Chassis SC111LT-330CB Form Factor: 1U rackmount Dimensions: (WxHxD) 16.8 x 1.7 x 21.95 in. (427 x 43 x 558 mm) Weight Gross (Bare Bone): 30 lbs. (13.6 kg.) System Cooling Three 4-cm heavy-duty counter-rotating PWM fans...
Page 95
Appendix B: System Specifi cations California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”...