Page 2
OWNER’S MANUAL 1200/2000/3000 WATT SERIES HIGH SURGE POWER INVERTERS...
Page 3
If you have questions concerning the operation of this Whistler product please call customer service: 1-800-531-0004 Hours: Monday - Friday 8:00 am - 5:00 pm CT Please keep the receipt in a safe place. You may register your product online at www.whistlergroup.com.
Page 4
Our mission is to provide products that improve your driving experience. Whistler offers a complete line of DC to AC inverters ranging in capacity from 100 Watts to 3000 Watts. These inverters offer advanced technology, dependable operation and will provide years of reliable service when used in accordance with our operating instructions.
TABLE OF CONTENTS Topic Page Features Summary ..............3-7 Important Information..............8 Inverter Information ............9 - 11 • Getting Started • Don’t Push It Battery Information ............11 - 13 • Selecting the Optimum Power Source Cable Information .............13 - 14 • Wire Cable Gauges Operation ................15 - 23 •...
Page 6
WHISTLER FEATURES A Word About Whistler Power Inverters Whistler inverters convert low voltage, direct current (DC) to 110 volt alternating household current (AC). The AC output is called “modified sine wave”. See “Technical Operating Principles” section for more information. Depending on the model and its...
Page 9
Operation Jack. The inverter is designed to be operated from a remote location via a WHISTLER Remote Control Switch (P/N 401010 wired or 401011 wireless) which plugs into this socket. This optional accessory is available through WHISTLER or your WHISTLER dealer.
Page 10
Despite this "built in" protection, the inverter may be damaged if the input voltage exceeds 15 volts DC and damage caused by excess voltage input is not covered under the WHISTLER warranty. N N o o t t e e : : In the event of automatic shut down or continuous audible alarm, turn the inverter OFF (O) until the source of the related problem has been determined and resolved.
This lower power requirement is referred to as the "continuous load." In order to ensure that the capacity of your Whistler inverter is sufficient to meet the required start up load, you must first determine the power consumption of the equipment or appliance you plan to operate.
INVERTER INFORMATION Don’t Push It. Although your Whistler power inverter has the capacity to provide power output (excess current) equal to approximately two times its rated wattage capacity for a very brief period, it is designed to operate equipment and appliances with start up load wattage ratings no higher than its own maximum continuous wattage rating.
Page 14
INVERTER INFORMATION start up load ratings comparable to your inverter wattage rating will not damage it. If a piece of equipment or an appliance will not operate, first confirm that the inverter has been properly connected to the 12 volt power source (See "Making The Connection"). If all connections have been properly made, turn the inverter rocker switch ON (l), OFF (O) and ON (l) again in quick succession.
10. The WHISTLER 1200 watt model utilizes 50 amps of battery power to operate an appliance with a 500 watt continuous load requirement. (500 divided by 10 = 50).
This multiple parallel battery option is especially recommended for the Whistler 3000 inverter due to the high level of amps these models require to produce up to 3000 watts of continuous load. For more information regarding battery power please visit our inverter faq page at www.whistlergroup.com/faq-inverters.asp.
CABLE INFORMATION The adapter is available through electronic supply or high end car audio installers. 2000 and 3000 When the inverter and the battery are set up within four feet of each other, use a minimum of #2 gauge wire to make the connections.
OPERATION Making the Connection. Make certain that the Power switch is in the OFF (O) position. Connect the cables to the power input terminals at the rear of the inverter and tighten the screws to make a secure connection. Do not use tools to tighten these screws. (To make these connections on the 2000 and 3000, remove the supplied nut at each terminal on the inverter, install the wire connectors flush with the metal backing...
Reverse polarity will blow the internal fuses in the inverter and may cause permanent damage to the inverter. Damage caused by reverse polarity is not covered under the Whistler warranty. • Making the connection between the Positive (+) terminals may cause a spark as a result of current flowing to the capacitors in the inverter.
OPERATION Turn the inverter ON (I). Check the Meter on the front panel. The Voltage should read between 11 and 14 volts depending on the voltage of the power source. If the reading is not within this range, check the voltage of the power source and the terminal connections on the power source and the inverter to make sure they are secure.
OPERATION • Check frequently to ensure that the input and output connections are secure. Loose connections may damage the inverter, the power source, or may generate excessive heat. • The following precautions apply to the 3000 watt models only. To generate the maximum output, the 3000 watt model should be connected to a power supply which has the capacity to produce up to 300 amps.
OPERATION The Power Source. When the engine is off, most batteries will provide ample power supply to the inverter for one to two hours. The actual length of time is a function of several variables including the age and condition of the battery, the number of batteries and the power demand being placed on it by the equipment being operated with the inverter.
OPERATION 2. Change the relative positions of the inverter, antenna cables and television power cord. 3. Isolate the television, its power cord and antenna cables from the 12 volt power source by running an extension cord from the inverter to the television set. 4.
Some Powerful Advice. Your Whistler inverter will work best when placed on a reasonably flat surface. The floor or wall of your vehicle are good locations. When driving with the inverter in operation, make certain that neither the inverter nor the power cords will impede safe operation of your vehicle.
For You Technical Types. 1. Basic Operating Principles: Whistler inverters work in two stages. During the first stage, the DC to DC converter increases the DC input voltage from the power source (e.g. a 12 volt battery) to 145 volts DC. In...
Page 26
The modified sine wave produced by your Whistler Inverter The modified sine wave produced by your Whistler inverter has a root mean square (RMS) voltage of 110 volts. The majority of AC voltmeters are calibrated for RMS voltage and assume that the measured waveform will be a pure sine wave.
OPERATING PRINCIPALS/SUMMARY A true sine wave typical of home AC outlet. In Review. • Never attempt to operate your Whistler inverter from any power source other than a 12 volt battery or a group of batteries that total 12 volts. •...
OPERATION SUMMARY • Before attempting to use a battery charger see page 18. • Before attempting to use medical equipment see page 8. • Use the heaviest gauge wire (smaller the number, the larger or heavier the cable) available to connect the inverter to the power source.
OPERATION SUMMARY • Always operate the inverter in accordance with the instructions in this manual. Failure to do so may result in property damage, personal injury, or loss of life. • While connecting the inverter to the power source, make certain that the inverter is well removed from any potential source of flammable fumes or gases.
TROUBLESHOOTING PROBLEM: TV Interference Problem Solution Electrical interference from Add a Ferrite data line filter inverter. on to the TV power cord. This filter is available at RadioShack, or other electronic supply stores. part number 273-105. PROBLEM: Low or No Output Voltage Problem Solution Using incorrect type of...
TROUBLESHOOTING Overload or High Temp LED on Problem Solution Equipment has a high Turn inverter power switch start up surge. OFF (O) and then ON (l) again until the inverter powers your appliance. Repeat as necessary to get your appliance "started".
SPECIFICATION WHISTLER 1200 WATT INVERTER SPECIFICATIONS Maximum Continuous Power……………………………1200 Watts Maximum Surge Capability (Peak Power).....2400 Watts* * No Load Current Draw………………………………....< 1.3A Waveform……………………………….....Modified Sine Wave Operating Input Voltage Range……………..11-15+0.5 Volts DC AC Receptacle……………………....Dual 3 (Prong Grounded) Approximate Dimensions......... 11” L x 6” W x 3” H Approximate Weight………………....……………..4.5 lbs...
Page 33
All express or implied warranties for this product are limited to (2) two years. Whistler is not liable for damages arising from the use, misuse, or operation of this product.
Page 34
WARRANTY IMPORTANT: Whistler will not assume responsibility for loss or damage incurred in shipping. Therefore, please ship your inverter insured with return receipt requested. 2. Include with your unit the following information, clearly printed: • Your name and street address (for shipping via UPS), a daytime telephone number, (No P.O.
Page 35
WARRANTY The out of warranty service fee for your 1200 Whistler inverter is $90.00, 2000 Whistler inverter is $150.00 and 3000 Whistler inverter is $250.00. If you require out of warranty service, please return your inverter as outlined in the section “Service Under Warranty”...