Before You Call For Service; Maintenance - Maytag MGR4410B User Manual

Maintenance

How to Remove Range
for Cleaning and Servicing
Follow these procedures to remove appliance for cleaning
or servicing:
1. Shut off gas supply to appliance.
2. Disconnect electrical supply to appliance, if equipped.
3. Disconnect gas supply tubing to appliance.
4. Slide range forward to disengage range from the anti-tip
bracket. (See Installation Instructions for location of
bracket.)
5. Reverse procedure to reinstall. If gas line has been dis-
connected, check for gas leaks after reconnection. NOTE:
A qualified servicer should disconnect and reconnect the
gas supply.
6. To prevent range from accidentally tipping, range must
be secured to the floor by sliding rear leveling leg into the
anti-tip bracket.

Before You Call for Service

Check these points if . . .
Part or all of the
appliance does not
work.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Surface burner
fails to light.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
The flame
is uneven.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Surface burner flame
lifts off ports.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Baking results differ
from previous oven.
(continued)
• Check to be sure plug is securely inserted into receptacle.
• Check or re-set circuit breaker. Check or replace fuse.
• Check power supply.
• Check if surface and/or oven controls have been properly set. See pages 6 and 8.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
• Check to be sure unit is properly connected to power supply.
• Check for a blown circuit fuse or a tripped main circuit breaker.
• Check to be sure burner ports or ignition ports are not clogged. See page 6.
• Check to be sure ignitor is dry and clicking. Burner will not light if ignitor is damaged, soiled or wet.
If ignitor doesn't click, turn control knob OFF.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
• Burner ports may be clogged.
• Flame setting may need to be adjusted.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
• Check to be sure a pan is sitting on the grate above.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
• Temperatures often vary between a new oven and an old one. As ovens age, the oven temperature
often "drifts" and may become hotter or cooler.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Proportional Valve Adjustment
for Surface Burners
The WARM setting should pro-
duce a stable flame when turn-
ing the knob from HIGH to
WARM. The flame should be
1
/ inch or lower and must be
8
stable on all ports on WARM
setting.
To adjust: Operate burner on HIGH for about five min-
utes to preheat burner cap. Turn knob back to WARM; re-
move knob, and insert a small screwdriver into the center
of the valve stem. Adjust the flame size by turning adjust-
ment screw in either direction, while holding the stem.
Flame must be of sufficient size to be stable on all burner
ports. If flame adjustment is needed, adjust ONLY on the
WARM setting. Never adjust flame size on a higher set-
ting.
NOTE: All gas adjustments should be done by a quali-
fied servicer only.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
13
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○