Download Print this page
Extron electronics RGB 440 User Manual

Extron electronics RGB 440 User Manual

Computer video and audio interface

Advertisement

Quick Links

Specifications
Specifications
Video
Gain ... Unity (0.7V), 15% with 3dB peaking (0.9V), 30% with
Bandwidth ... 300 MHz (-3dB)
Video input
Number/signal type ... 1 analog RGBHV, RGBS, RGsB
Connectors ... 1 9-pin male for MBC cable or buffer
Nominal level(s) ... Analog — 0.3V to 1.45V p-p
Impedance ... 75 ohms or Hi Z, switchable
Horizontal frequency ... 15 kHz to 150 kHz (optimum 15 kHz to 62 kHz)
Vertical frequency ... 30 Hz to 170 Hz
Video output
Number/signal type ... 1 analog RGBHV, RGBS, RGsB
Connectors ... 6 BNC female
Nominal level ... Analog 0.7V p-p, 0.8V p-p, or 0.9V p-p w/ peaking
Impedance ... 75 ohms
Return loss ... -30dB @ 5 MHz
Sync
Input type ... Autodetect RGBHV, RGBS, RGsB (accepts RGsB but
Output type ... RGBHV at all times, RGBS at all times, RGsB only when
Input level ... 2V p-p to 5.5V p-p with ±0.2VDC offset max.
Output level ... 4V to 5V p-p
Input impedance ... 10 kohms
Output impedance ... 75 ohms
Max. propagation delay ... 50 nS
Max. rise/fall time ... 2.5 nS
Polarity ... Positive or negative
Audio
Gain ... Unbalanced 0dB, balanced +6dB
Frequency response ... ±0.05dB @ 20 Hz to 20 kHz
THD + Noise ... 0.03% @ 1 kHz, 0.3% @ 20 kHz at rated max. output
S/N ... >90dB, output 14dBu, balanced
Stereo channel separation ... >95dB @ 1 kHz to 20 kHz
Audio input
Number/type ... 1 stereo, unbalanced; 1Vrms (+4dBu), 20 Hz to 20 kHz
Connectors ... 1 3.5 mm stereo jack (2 channel), unbalanced; tip (R),
Impedance ... 10 kohms, DC coupled
Min/max levels ... 100mV / +8.5 dBu
Audio output
Number/type ... 1 buffered, stereo (2 channel), balanced or unbalanced
Connectors ... 1 3.5 mm captive screw connector, 5 pole
Impedance ... 50 ohms unbalanced, 100 ohms balanced
Gain error ... ±0.1dB channel to channel
Drive (600 ohm) ... > +14dBu, balanced at stated %THD+N
General
Power ... 12 to 24VAC or VDC, 0.5 A, 5 watts, external (Order
MBC power jack ... 9VDC, 0.15 A
Temperature/humidity (non condensing) ... Storage -40° to +158°F (-40° to +70° C ) / 10% to 90%
Metal enclosure dimensions ... 1.0" H x 5.7" W x 4.5" D (7" W with mounting brackets)
Shipping weight ... 2 lbs. (0.9 kg)
Vibration ... NSTA 1A in carton (National Safe Transit Association)
Approvals ... UL, CE, FCC Class A
MTBF ... 30,000 hours
Warranty ... 3 years parts and labor
Extron Electronics, USA
Extron Electronics, Europe
1230 South Lewis Street
Beeldschermweg 6C
Anaheim, CA 92805
3821 AH Amersfoort
USA
The Netherlands
714.491.1500
+31.33.453.4040
www.extron.com
Fax 714.491.1517
Fax +31.33.453.4050
© 2002 Extron Electronics. All rights reserved.
... 6dB peaking (0.9V)
... does not strip sync from video)
... input is RGsB
... ring (L), sleeve (ground)
... the power supply separately, part number 70-055-01.)
... Operating +32° to +122°F (0° to +50° C) / 10% to 90%
... 2.54 cm H x 14.48 cm W x 11.43 cm D (17.7 cm W)
Extron Electronics, Asia
Extron Electronics, Japan
135 Joo Seng Road, #04-01
Daisan DMJ Building 6F
PM Industrial Building
3-9-1 Kudan Minami
Singapore 368363
Chiyoda-ku, Tokyo 102-0074 Japan
+65.6383.4400
+81.3.3511.7655
Fax +65.6383.4664
Fax +81.3.3511.7656
User's Guide
RGB 440 Interface
Computer Video and Audio
68-378-01 Rev. E
Printed in the USA
01 02

Advertisement

loading

Summary of Contents for Extron electronics RGB 440

  • Page 1 Shipping weight ... 2 lbs. (0.9 kg) Vibration ... NSTA 1A in carton (National Safe Transit Association) Approvals ... UL, CE, FCC Class A RGB 440 Interface MTBF ... 30,000 hours Warranty ... 3 years parts and labor Computer Video and Audio...
  • Page 2 With DDSP enabled, the H Shift control (F) on the front panel is defeated. The RGB 440 may be mounted under, or on the side, of a table or desk using the included Under Desk Mounting Kit, as shown in figure 1 and as detailed in the kit’s Jumpers documentation (68-461-01).
  • Page 3 Power The RGB 440 requires an external voltage source of 12 to 24 volts AC or DC (500 mA max). Polarity is not an issue, even if the power source is a DC voltage. Simply insert the power plug into the connector labeled POWER ((H) on figure 2) on the rear panel of the RGB 440.