Technical Specifications; Conformity Certificates; Technical Data; Ec Declaration Of Conformity - Husqvarna Soff-Cut 2500 Operator's Manual

Engine
Model Honda GX 390
Engine oil volume, 1.2/1.1
quarts/liters
Gasoline tank 1.7/6.5
volume, gal/liters
Type cooled, 4-cycle, single slant cylinder,
overhead valves, gasoline engine
Air fi lter Cyclonic type
Oil system Oil alert with auto shut down sensor
Muffl er Silent type 100 dbA, exhaust defl ector,
spark arrestor
Emissions Complies with EPA Phase 2 and CARB
Tier II USA regulations
Cooling Air cooled
Cylinder Aluminum with cast iron liner
Controls Engine mounted manual fuel shut off
lever Instrument panel mounted manual
choke, electric switch operated throttle,
keyed on/off switch.
Weight and Dimensions
Weight – dry, lbs/kg
Weight with gasoline and oil full, lbs/kg
Length (handle folded in), inch/mm
Width, inch/mm
Height, inch/mm
Blade
Material cut Green concrete only
Blade type 10.0" (254 mm) or 9.0" (229 mm) dry cut
with tri-arbor
CALIFORNIA AIR RESOURCES BOARD (CARB): This machine is considered a preempt Off-Road Application as relating to CARB stan-
dards. Under construction equipment, and in particular, as a Saws : concrete, masonry, cutoff, with engine power less than 19KW (25hp),
CARB standards do not apply to this machine.
For more information see the website

EC DECLARATION OF CONFORMITY

Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna Soff-Cut 2500
dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with
the requirements of the COUNCILíS DIRECTIVE:
• of May 17, 2006 "relating to machinery" 2006/42/EC
• of December 15, 2004 "relating to electromagnetic compatibility" 2004/108/EC.
• of May 8, 2000 "relating to the noise emissions in the environment" 2000/14/EC.
The following standards have been applied: EN ISO 12100:2003, EN 55014-1:2006, EN 55014-2/A1:2001, EN 61000-3-2:2006, EN 61000-
3-3/A1/A2:2005, EN 13862/A1:2009.
Huskvarna December 29, 2009
Henric Andersson
Vice President, Head of Power Cutters and Construction Equipment
(Authorized representative for Husqvarna AB and responsible for technical documentation.)

TECHNICAL SPECIFICATIONS

336/152
348/158
50/1270
23/584
38/965

TECHNICAL DATA

http://www.arb.ca.gov/msprog/offroad/preempt.htm
Blade rotation Counter clockwise, upcutting
Blade shaft speed, 3200
rpm
Cutting depth 1 to 1 1/2 inch (25 to 38 mm) depending
on amount of blade wear
Cutting distance 3 1/2 / 89
from wall, inch/mm
Average cutting rate - Estimate only. Speed will vary with job
conditions and concrete mixes.
Soft aggregates, ft/min / m/min
Medium aggregates, ft/min / m/min
Hard aggregates, ft/min / m/min
Blades are available in 10.0 inch (254 mm) and 9.0 inch (229 mm)
diameters and in 0.100 inch (2.5 mm), 0.250 inch (6.4 mm), 0.380
inch (9.7 mm), and 0.500 inch (12.7 mm) widths.
Noise emissions (see note 1)
Sound power level, measured dB(A)
Sound power level, guaranteed dB(A)
Sound levels (see note 2)
Sound pressure level at the operators ear, dB(A)
Vibration levels, a (see note 3)
hv
Handle right, m/s
2
Handle left, m/s
2
Note 1: Noise emissions in the environment measured as sound
power (L ) in conformity with EC directive 2000/14/EC.
WA
Note 2: Noise pressure level according to EN 13862. Reported
data for noise pressure level has a typical statistical dispersion
(standard deviation) of 1.0 dB(A).
Note 3: Vibration level according to EN 13862. Reported data for
vibration level has a typical statistical dispersion (standard devia-
tion) of 1 m/s .
2
20/6.1
14/4.3
8/2.4
109
110
91
3,4
3,6