Related Manuals for CHAINTECH 9EJL4
Summary of Contents for CHAINTECH 9EJL4
- Page 1 9EJL4 Intel® Socket 478 Intel® 845PE + ICH4 ATX Motherboard User’s Guide Version 1.0...
-
Page 2: Declaration Of Conformity
According to 47 CFR, Parts 2 and 15 of the FCC Rules The following designated product: EQUIPMENT: MAINBOARD MODEL NO.: 9EJL4 is a Class B digital device that complies with 47 CFR Parts 2 and 15 of the FCC Rules. Operation is subject to the following two conditions: 1. -
Page 3: Federal Communications Commission Statement
Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: * This device may not cause harmful interference. * This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 4: Table Of Contents
3-11 Save and Exit Setup ..................31 3-12 Exit Without Saving ..................31 DRIVER Setup............32 Chapter 4 4-1 Intel® IDE Bus Mastering Drivers Setup............32 4-2 Ultra ATA storage driver Setup..............32 4-3 Audio Driver Setup..................33 4-4 LAN Driver Setup ..................33 4-5 USB 2.0 Driver ....................33... -
Page 5: Chapter 1 Introduction
Processor Supports Intel® Celeron/Pentium 4 Socket 478 CPU with Hyper-Threading Technology Supports Intel® Celeron / Pentium 4 system bus at 400/533/800MHz (FSB 800 is conditionally supported. Please refer to Memory Compatibility Chart for details) Chipset Intel® 845PE + ICH4 Chipset... -
Page 6: Package Contents
Chapter 1 Fast Ethernet /Home Networking Controller On-board LAN chip RTL8101L supports 10/100Mbps Fast Ethernet Boot-Block Flash ROM Award system BIOS supports PnP, APM, DMI, ACPI, & Multi-device booting features. 1-2 Package Contents This product comes with the following components: 1. -
Page 7: 9Ejl4 Motherboard Layout
Chapter 1 1-3 9EJL4 Motherboard Layout... -
Page 8: Chapter 2 Hardware Setup
Not doing so may result in electrical shock! 2-1 Installing a CPU Processor for Socket 478 The Intel® Socket 478, designed for the Pentium 4 processor, has been incorporated as a standard motherboard specification. This motherboard will support Intel®... -
Page 9: Setting Your Cpu's Parameters
To enabling the functionality of Hyper-Threading Technology for your computer system you require ALL of the following platform components: CPU: An Intel® Pentium® 4 Processor with HT Technology; Chipset: An Intel® Chipset that supports HT Technology; BIOS: A BIOS that supports HT Technology and has it enabled;... -
Page 10: Main Memory Configuration
Chapter 2 2-3 Main Memory Configuration This motherboard provides 2 184pin Double Data Rate (DDR) Dual Inline Memory Modules (DIMM) slots, which supports PC 1600/PC2100/2700 DDR SDRAM modules up to 2GB. Install at least one DIMM module on the slots. Memory modules can be installed on the slots in any order. -
Page 11: Connector And Jumper Settings
Chapter 2 2-4 Connector and Jumper Settings Connectors are used to link the system board with other parts of the system, including power supply, keyboard, and the various controllers on the front panel of the system case. The power supply connector is the last connection to be made while installing a motherboard. - Page 12 Chapter 2 Blinking LED in Suspend Mode: While in Suspend mode, the LED light on the front panel of your computer will flash. Suspend mode is entered by pressing the Green Override Power Button on your ATX case, or by enabling the Power Management and Suspend Mode options in BIOS's Power Management menu.
- Page 13 Chapter 2 Button Operation diagram. 2. P-LED (Power LED Connector): The power indicator LED shows the system's power status. It is important to pay attention to the correct cable and pin orientation (i.e., not to reverse the order of these two connectors.) 3.
- Page 14 Chapter 2 IDE 1/2 (IDE Hard-Disk Connector) The motherboard has a 32-bit Enhanced PCI IDE and Ultra ATA66/100 controller that provides PIO mode 0~4, Bus Master, and Ultra ATA66/100 function. This connector is used for connecting 40 pins of ATAPI devices. IDE 1 only connects two IDE devices.
- Page 15 Chapter 2 1. Disconnect the system power supply from the power source. 2. Set the jumper cap at location [2-3] for <5 seconds>, and then set it back to the default position. 3. Connect the system's power and then start the system. 4.
- Page 16 Chapter 2 FAN1/FAN2/FAN3 (CPU/System/ North Bridge Cooling Fan Connectors): The board's hardware management is able to detect the CPU and system fan speed in rpm (revolutions per minute). The wiring and plugging may vary depending on the manufacturer. On standard fans, the red is positive (+12V), the black is ground, and the yellow wire is the rotation signal.
- Page 17 Chapter 2 CN5 [WOL (Wake-on-LAN) Connector]: Enable the Wake Up On LAN selection in BIOS's Power Management Menu to use this function. The capability to remotely manage PCs on a network is a significant factor in reducing administrative and ownership costs. Magic Packet technology is designed with WOL capability to LAN controller.
- Page 18 Chapter 2 CN23/CN23A (CBOX™ 2 Front USB Connector for USB 2/3 and 4/5): USB Port 2/3 CN23, USB Port 4/5 CN23A If you want to use a USB Keyboard, you must enable the USB keyboard support function in BIOS's Integrated Peripherals menu (See Section 3.4). This board contains a USB Host controller and a root hub with two connectors is also included for an optional USB Adaptor (USB 2/3 and 4/5).
-
Page 19: Chapter 3 Bios Setup Program
Chapter 3 BIOS Setup Program Chapter 3 Phoenix-Award BIOS ROM has a built-in setup program that allows users to modify the basic system configuration. This information is stored in CMOS RAM so that it can retain the setup information, even when the power is turned off. To enter the Phoenix-Award BIOS setup program press [Delete] when you Power on or reboot the computer system. -
Page 20: Standard Cmos Setup
Chapter 3 3-1 Standard CMOS Setup The Standard CMOS Setup allows users to configure system components such as hard disk drive, floppy disk drive and video display as well as date, time and boot-up error signaling. This configuration menu should be changed when installing a motherboard for the first time, changing hardware in your system such as the HDD, FDD, video display, or when the CMOS data was lost or corrupted. -
Page 21: Advanced Bios Features
Chapter 3 POST (Power On Self Test). This function stops the computer if BIOS detects a hardware error. You can tell BIOS to halt on all errors, no errors, or not to halt on specific errors. 3-2 Advanced BIOS Features By choosing the Advanced BIOS Features option from the CMOS Setup Utility menu (Figure 3-1), the screen below displays the manufacturer's default values for the motherboard. - Page 22 Chapter 3 Hyper-Threading Technology Available options are [Enabled] and [Disabled]. Select [Enable] to support Hyper-Threading Technology and vice versa. Quick Power On Self Test (POST): Enable this function to reduce the amount of time required to run the POST (Power On Self Test).
- Page 23 Chapter 3 3. Typematic Delay (Msec) The typematic delay sets how long after you press a key that a character begins repeating. Security Option: The Supervisor and/or User Password functions shown in Figure 3-1 must be set to take advantage of this function. See Section 3.11 for password setting information. When the Security Option is set to System, a password must be entered to boot the system or enter the BIOS setup program.
-
Page 24: Advanced Chipset Features
Chapter 3 3-3 Advanced Chipset Features By choosing the [Advanced Chipset Features] option from the CMOS Setup Utility menu (Figure 3-1), the screen below displays the manufacturer's default values for the motherboard. Figure 3-4 Advance Chipset Features All of the above settings have been determined by the motherboard manufacturer and should not be changed unless you are absolutely sure of what you are doing. - Page 25 Chapter 3 DRAM RAS# Precharge: This item controls the idle clocks after issuing Precharge command to the DRAM. System BIOS Cacheable: Enabling this function allows caching of the system BIOS ROM at F0000h-FFFFFh, which results in better system performance. However, if any program writes to this memory area, a system error may result.
-
Page 26: Integrated Peripherals
Chapter 3 3-4 Integrated Peripherals This section provides information on setting peripheral devices. By choosing the Integrated Peripherals option from the CMOS Setup Utility menu (Figure 3-1), the screen below displays the manufacturer's default values for the motherboard. Figure 3-5 Integrated Peripherals Screen OnChip IDE Device: Press [Enter] to enter the sub-menu, which contains the following items for advanced control:... - Page 27 Chapter 3 support. OnChip PCI Device: This section provides information on setting the on-board devices. Press [Enter] to enter the sub-menu, which contains the following items for advanced control: 1. AC97 Audio: This feature allows you to enable/disable the on-board AC97 audio function. Super IO Device: This section provides information on setting the Super I/O devices.
- Page 28 Chapter 3 10. Midi Port IRQ: This item specifies an IRQ for the Midi port. USB controller: Enable the on-board Universal Serial Bus (USB V1.1 or V2.0) controller if you want to connect a USB device to your system. Note that if this setting is disabled, you can still temporarily use a USB keyboard during boot up so that you can enter BIOS and enable this setting.
-
Page 29: Power Management Setup
Chapter 3 3-5 Power Management Setup This section provides information on the Green PC power management functions. By choosing the Power Management Setup option from the CMOS Setup Utility menu (Figure 3-1), the screen below displays the manufacturer's default values for the motherboard. - Page 30 Chapter 3 selected Blank. This function serves as both screen and a power saver. 3. DPMS Supported - Select this option if your video card supports the Display Power Management Signaling (DPMS) standard (i.e., you have a monitor that supports Green features). Use software supplied by your video subsystem to set video power management options.
- Page 31 Chapter 3 Wake up Events 1. Power On By PCI/Onbrd LAN: When enabled, a PCI interface that receives a signal will activate the system from soft off and green mode. 2. Power On by Modem: When enabled, a Modem will be able to receive a signal and activate the system from soft off and green mode.
-
Page 32: Pnp/Pci Configurations
Chapter 3 3-6 PNP/PCI Configurations This section provides IRQ and DMA setting information. By choosing the PNP/PCI Configuration option from the CMOS Setup Utility menu (Figure 3-1), the screen below displays the manufacturer's default values for the motherboard. Figure 3-6 PNP/PCI Configurations Reset Configuration Data: Default is [Disabled]. -
Page 33: Frequency/Voltage Control
Chapter 3 3-7 Frequency/Voltage Control By choosing the Frequency/Voltage Control option from the CMOS Setup Utility menu (Figure 3-1), the screen below displays the manufacturer's default values for the motherboard. Figure 3-8 Frequency/Voltage Control Memory Frequency For Please leave the default system setting [Auto] for a stable system operation. CPU Clock Ratio: This feature allows user to manually configure your CPU clock ratio according to your processor’s specifications. -
Page 34: Load Fail-Safe Defaults
Chapter 3 Overclockability: This motherboard is designed to support overclocking ability. However, please make sure your components are able to tolerate such abnormal setting, while CPU clock speed is overclocked. Any attempt to operate are not beyond product specifications is not recommended. We responsible caused by inadequate operation for damages... -
Page 35: Save And Exit Setup
Chapter 3 When there is no supervisor password set, the user password controls access to all BIOS settings. 3-11 Save and Exit Setup If you select this and type [Y] (for Yes) followed by [Enter], the values entered in the setup utilities will be recorded in the CMOS memory of the BIOS chip. 3-12 Exit Without Saving Selecting this option and pressing [Y] followed by [Enter] lets you exit the Setup program without recording any new values or changing old ones. -
Page 36: Chapter 4 Driver Setup
Insert the support CD that come with your motherboard into your CD-ROM driver or double-click the CD drive icon in [My computer] to open the setup screen. 4-1 Intel® IDE Bus Mastering Drivers Setup 1. Click [Intel® IDE Bus Mastering Drivers] 2. -
Page 37: Audio Driver Setup
6. Please click [Print to File] to continue. 7. Please click [OK] to continue. 8. Click [Finish] to complete setup. 4-6 Intel® LAN Driver Setup 1. Click [LAN Driver] 2. Click [Next] to continue installation 3. Click [Finish] to complete setup... - Page 38 How To Contact CHAINTECH NOTE All rights are reserved for the products and corporate names/logos that appear in this manual to their original owners. CHAINTECH reserves all the rights to change this manual .All information is subject to change without notice.
- Page 39 NOTE How To Contact CHAINTECH Please do not hesitate to contact us if you have any problem about our products. Any opinion will be appreciated. For Asia, Africa, Australia and Pacific Island: For UK: CHAINTECH COMPUTER CO., LTD CHAINTECH UK., LTD. No.