Page 1
10/100Mbps Fast Ethernet Switch FSD-805/FSD-805SC/FSD-805ST/FSD-805S15 User's Manual...
Page 2
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 8-Port 10/100Mbps Fast Ethernet Switch User's Manual For Models: FSD-805 / FSD-805SC / FSD-805ST / FSD-805S15 Revision: 1.1 (February, 2009) Part No: EM_FSD805v1.1 (2350-A31150-001)
1. I NTRODUCTION 1.1 Package Contents Check the contents of your package for following parts: Fast Ethernet Switch x 1 User's manual x 1 Power cord x 1 Rubber feet x 4 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
1.3 Product Features Complies with the IEEE 802.3 Ethernet and IEEE 802.3u Fast Ethernet standard Features Store-and-Forward mode with wire-speed filtering and forwarding rates Support 2K MAC address table Support to handle up to 1522 bytes packet size LED indicators for simple diagnostics and management Hardware based 10/100Mbps auto-negotiation Full / Half-Duplex capability on every TX ports, total band- width is up to 200Mbps per port...
1.4 Product Specifications Product FSD-805 FSD-805SC FSD-805ST FSD-805S15 Hardware Specification 10/100Base-TX Ports 100Base-FX SC Port 100Base-FX ST Port Dimensions (W x D x H) 191 mm x 85 mm x 26 mm Weight 325g Power Requirement Internal power 100-240V AC, 50/60Hz, 0.2A Power Consumption / Dissipation 4.3 watts / 14.6 BTU...
805S15; term of “switch” can be any third part switches. 2.1 Product Description The PLANET FSD-805 / FSD-805SC / FSD-805ST and FSD- 805S15 are 10/100Mbps Fast Ethernet Switches in a compact housing for easily desktop placement. With 8 ports respectively and it’s Auto-negotiation capability, all the RJ-45 ports can...
FSD-805SC / FSD-805ST and FSD-805S15, the fiber transmit distance can be 2km and 15km. 2.1.2 Switch Front Panel Figure 2-1 & 2-2 & 2-3 & 2-4 shows a front panel of FSD-805 / FSD-805SC / FSD-805ST and FSD-805S15. Figure 2-1 FSD-805 front panel...
Blink: indicate that the Switch is actively sending or receiving data over that port. 2.1.4 Switch Rear Panel Figure 2-5 shows a rear panel of FSD-805 / FSD-805SC / FSD- 805ST and FSD-805S15. Figure 2-5 FSD-805 / FSD-805SC / FSD-805ST / FSD-805S15 rear panel 1.
2.2 Installing the Switch This part describes how to install your Fast Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented. This Switch does not need software configuration. Note 2.2.1 Desktop Installation To install the Switch on desktop, simply follow the next steps:...
Page 12
Step 5: Supply power to the Switch. A. Connect one end of the power cable to the Switch. B. Connect the power plug of the power cable to a standard wall outlet. When the Switch receives power, the Power LED should remain solid Green.
3. SWITCH OPERATION 3.1 Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Switch.
3.4 Store-and-Forward Store-and-Forward is one type of packet-forwarding techniques. A Store-and Forward Ethernet Switching stores the incoming frame in an internal buffer, do the complete error checking before transmission. Therefore, no error packets occurrence, it is the best choice when a network needs efficiency and stability. The Ethernet Switch scans the destination address from the packet-header, searches the routing table provided for the incoming port and forwards the packet, only if required.
3.5 Auto-Negotiation The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible bandwidth when a connection is established with another network device (usually at Power On or Reset). This is done by detect the modes and speeds at the second of both device is connected and capable of, both 10Base-T and 100Base-TX devices can connect with the port in either Half- or Full-Duplex mode.
4. TROUBLESHOOTING This chapter contains information to help you solve issues. If the Switch is not functioning properly, make sure the Fast Ethernet Switch was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Switch.
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Straight Cable SIDE 1 SIDE2 1 = White / Orange 1 = White / Orange SIDE 1 2 = Orange 2 = Orange...