Comtech EF Data Vipersat CDD-562L User Manual page 12

Figure 3-62 Home State Configuration screen3-48
Figure 3-63 Force Modem to Home State warning
3-49
Figure 3-64 Receive Frequency prompt . . . . . 3-49
Figure 3-65 Receive Data Rate prompt . . . . . 3-50
Figure 3-66 Receive FEC Type prompt . . . . . 3-50
Figure 3-67 Receive Coding Rate prompt . . . 3-50
Figure 3-68 Receive Modulation Type prompt 3-51
Figure 3-69 Vipersat Summary screen. . . . . . 3-51
Figure 3-70 Vipersat Migration prompt . . . . . . 3-53
Figure 3-71 UDP Port Base Address prompt . 3-53
Appendix A Figures
Figure A-1 The Seven OSI Protocol Layers . . .A-2
Figure A-2 Bits and Bytes. . . . . . . . . . . . . . . . .A-4
Figure A-3 Binary to Decimal Conversion . . . .A-4
Figure A-4 IP Address Classes A, B, C . . . . . .A-7
Figure A-5 NAT Router Example . . . . . . . . . . .A-8
Figure A-6 Default Subnet Masks for IP Classes .
A-9
Figure A-7 ANDing an IP address and a subnet
mask . . . . . . . . . . . . . . . . . . . . . . . . . .A-10
Figure A-8 Network Segments . . . . . . . . . . . .A-10
Figure A-9 Router as Default Gateway. . . . . .A-11
Figure A-10 Network Node MAC Addresses .A-12
Appendix B Figures
Figure B-1 Hitless Switching screen. . . . . . . . .B-2
Figure B-2 Auto Switching Menu, CDM-570/570L
Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-8
Figure B-3 Hub Load Switching Page, SLM-5650A
B-8
Figure B-4 Auto Switching Menu, CDM-570/570L
Remote . . . . . . . . . . . . . . . . . . . . . . . .B-11
Figure B-5 Remote Load Switching Page, SLM-
5650A . . . . . . . . . . . . . . . . . . . . . . . . .B-11
Figure B-6 Load Switching diagram . . . . . . . .B-13
Figure B-7 Application Switching diagram . . .B-16
Figure B-8 ToS Field Location within the IP Header
B-18
Figure B-9 Remote ToS Switching menu . . . .B-20
Figure B-10 Per Device ToS Switching Example .
B-21
vi
Figure B-11 Per Type ToS Switching Example . .
B-22
Figure B-12 ToS Remarking Application . . . B-23
Figure B-13 ToS and DSCP Conversion Chart . .
B-23
Figure B-14 ECM Switch Recovery: < 3 minutes .
B-27
Figure B-15 ECM Switch Recovery: > 3 minutes .
B-28
Figure B-16 STDMA Page with Entry Channel
Mode, CDM-570/570L . . . . . . . . . . . . B-29
Figure B-17 ECM Remote List Page, CDM-570/
570L . . . . . . . . . . . . . . . . . . . . . . . . . . B-30
Figure B-18 Remote Bandwidth Entry, CDM-570/
570L . . . . . . . . . . . . . . . . . . . . . . . . . . B-30
Figure B-19 Revert Uplink Carrier Command, VMS
modem . . . . . . . . . . . . . . . . . . . . . . . . B-31
Figure B-20 Entry Channel Mode v2 Configuration,
Hub (CDD-564L) . . . . . . . . . . . . . . . . B-33
Figure B-21 Entry Channel Mode v2 Configuration,
Remote (CDM-570L) . . . . . . . . . . . . . B-34
Figure B-22 ECMv2 Processing Diagram . . . B-35
Appendix C Figures
Figure C-1 Data Rate to Power Relationship, DPC
C-5
Figure C-2 Excessive Max Power Example . . C-6
Figure C-3 DPC Configuration screen, CLI . . C-9
Figure C-4 DPC dialog, Parameter Editor . . C-10
Figure C-5 DPC Calculate Max Power screen, CLI
C-12
Figure C-6 DPC Calibration dialog, Parameter
Editor . . . . . . . . . . . . . . . . . . . . . . . . . C-12
Figure C-7 Signal Power Levels, Remote SiteC-15
Appendix D Figures
Figure D-1 STDMA Configuration Page, Remote
CDM-570/L. . . . . . . . . . . . . . . . . . . . . . D-4
Figure D-2 STDMA Configuration Menu, Hub Type
Selection . . . . . . . . . . . . . . . . . . . . . . . D-5
Figure D-3 STDMA Menu, ECMv2 Hub Type . D-6
Figure D-4 Switch Rate Limits, InBand Return Path
Settings Page. . . . . . . . . . . . . . . . . . . . D-7
Vipersat CDD-56X Series User Guide
MN/22137, rev 1