Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hoover U3721
Summary of Contents for Hoover U3721
- Page 1 Self-Propelled Review this manual before operating cleaner...
- Page 2 Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Factory SeMce Center or Authorized Hoover Warranty Service Dealer (Depot).
- Page 3 A. Hose B. Furniture Nozzle C. Crevice Tool D. Dusting Brush E. Wands F. Paper Bag G. Fragrance Tablet (some models only) The assembled cleaner will look like the drawing above. Side-mounted hose trademark of The Hoover Company ‘...
-
Page 4: Cleaner Description
. Cleaner Description 1. Self Propel Handle Grip 2. OFF-ON-‘Power Surge’ Switch 3. Self Propel Control Button 4. Cord Storage Hooks: located on back of handle and lower edge of cloth bag. Upper hook rotates for easy cord release. 5. Bag Spring: place spring ring over hook to support the bag. 6. -
Page 5: How To Assemble
Attach hose With cleaner handle in lowest position, open hose door and insert hose end with tabs into cleaner. Turn hose end to lock in place. To remove hose, turn in opposite direction. Stretch hose over hose rack and push opposite hose end firmly into “cup”... -
Page 6: How To Use
Pull open tool cover. Snap furniture nozzle (A), crevice tool (B), and dusting brush (C) into front of cleaner as shown. Close tool cover. CAUTION: When cleaner is turned on, agitator will con- tinue to rotate while cleaner handle is in upright position. Avoid tipping cleaner or settlng it on carpeted stairs, trlnged area rugs, or furniture... -
Page 7: Handle Positions
Your cleaner also has a conve- nient carrying handle located just above the tool cover. Handle positions The handle of your cleaner has three positions: upright for storage and tool use; operating for general operation on carpet and floors; low for cleaning under low furniture. -
Page 8: Variable Speed Models
Some cleaners are equipped with a variable speed control. Self Propel feature Note: The Self Propel feature will operate only when motor is turned on. This feature moves the cleaner forward and backward at a variable rate of speed controlled entirely by you. Self Propel Control Button... -
Page 9: Special Features
Self Propel control button For increased control of the Self Propel feature in tight places such as around and under furniture, or on non-carpeted floors set the cleaner on the lowest speed setting, or push the control button to OFF to disengage the Self Propel mechanism. Special features Edge cleaning Brushed edge cleaning is... -
Page 10: Air Freshener Dis- Penser
Air freshener tablets may be obtained from your local authorized Hoover Dealer (Depot), a Hoover Factory Service Center, or by using the mail order form packed with your cleaner. -
Page 11: Cleaning Tools
release the cord, rotate top cord hook. The hook can then be repositioned for wrapping the cord. Cleaning tools Use tools with cleaner handle locked in upright position. The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descriptions below. -
Page 12: Maintenance
Where to buy Bags may be purchased from your local Authorized Hoover Dealer (Depot) or from a Hoover Factory Service Center or use the mail order form packed with your cleaner. sure to give the model number of your cleaner. - Page 13 99.9% of dust down to 5 microns, and,aids in returning clean air to the room. Regular HOOVER@ Tpye A disposable bags also fit your cleaner. To assure that your HOOVER cleaner operates at peak performance, it is imperative that you use only genuine HOOVER paper bags made by The Hoover Company.
- Page 14 The headlight Some models only. What to buy This cleaner uses two 12 volt, wedge base bulbs. Hoover part No. 27313105 to replace Disconnect cleaner from electrical outlet. 1. Lower handle until cleaner is positioned with bag flat on floor.
- Page 15 Self Propel feature. When buying new belts, you should always insist on genuine YOOVER parts. Other belts may not meet the Hoover design and quality control standards. They may not operate the agitator or ‘Power Drive’ transmission correctly and may cause damage.
-
Page 16: Agitator Belt
If they are stretched, cut, or broken, they should be replaced. What to buy Agitator belt - Hoover part No. 38528008 ‘Power Drive’ belt - Hoover part No. 160147 How to replace Agitator belt Disconnect cleaner from electrical outlet and detach hose from cleaner. - Page 17 3. To remove agitator, use a screwdriver placed as shown. 5. If the end plates have loosened, tighten them by turning in opposite directions. 7. Slip plastic pulley end of agitator through belt. (See illustration.) 4. Use one hand to remove the agitator as you use the end of the screwdriver for leverage.
- Page 18 9. Lift and pull, using screw- driver as a lever. Guide end opposite belt into position first. 11. Press firmly to be sure agitator is secure. 13. Maintaining front connec- tion, rotate bottom elate to covkr bottom of cleaner. Make sure dirt duct is in position under elate.
- Page 19 Disconnect cleaner from electrical outlet and detach hose from cleaner. To replace the (small) ‘Power Drive’ belt it is necessary to first remove the bottom plate, agitator and the larger agitator’belt, as shown on the previous pages. Note: It may not be necessary to change both belts at the same time.
-
Page 20: Clearing Obstructions
First, check dirt duct; then dirt tube. if an obstruction cannot be found or removed, contact your Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot). To check dirt duct Disconnect cleaner from electrical outlet and detach hose from cleaner. - Page 21 To check dirt tube Disconnect cleaner from electrical outlet. 1. Remove paper bag. Remove dirt tube by pushing to either side to release clips. Lift dirt tube up and out. 3. To replace dirt tube, position it over lower seal and push down.
- Page 22 To maintain cleaning effectiveness, replace brushes if they do not touch card. What to buy When purchasing new brushes, ask for HOOVER part No. 48445015. On some models, the agitator takes four brushes; other models have a two-brush agitator. Note the number of brushes your cleaner needs.
- Page 23 2. Pull or pry out end sections as shown in illustration. Note: Pulley end should be removed by pulling straight out. 3. Note position of bar/brush assemblies to insure correct replacement. Pull bar/brush assemblies out of agitator slots, using pliers if necessary.
- Page 24 The motor is equipped with self-lubricated bearings. lubricant to the motor; it could cause damage. The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot). Possible solution 1.
- Page 25 (Depot). For service under warranty, follow the instructions in the warranty provided with this product. Do not send your cleaner to The Hoover Company in North Canton for service as this will only result in a delay. Always identify your cleaner by the complete model number when requesting information or ordering parts.
-
Page 26: Energy Saving Tips
3. Turn cleaner off when not in use, such as when moving furniture. 4. Keep your cleaner operating at peak performance - have inspec- tion and service performed by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot). - Page 27 The Hoover Company wants to quickly resolve any concerns about your cleaner or questions regarding its use. However, do not send your cleaner to The Hoover Company in North Canton for service. This will only result in a delay. If you are not completely satisfied look on the list provided with the product for your local Hoover Factory Service Center or in the Yellow Pages under “Vacuum...