Related Manuals for Hoover WindTunnel U5720-960
Summary of Contents for Hoover WindTunnel U5720-960
- Page 1 Wind unnel Bagless Hoover Congratulations your purchase! This product was designed for easy assembly (see page 3) www.hoover.com...
- Page 2 • Do not use with damaged cord or plug. If appliance is not working as it should, been dropped_lamaged, left outdoors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot).
- Page 3 (U.S. only) 1-330-499-9499 to speak with a representative Consumer Response Center Visit on-line at www,hoover, to find service outlet nearest (click "Service" button). Carton contents Remove all parts from carton and identify each item shown. Make sure all parts are located before disposing of packing.
- Page 4 STEP 1 Attach handle Remove cardboard screws Make sure that switch is in Open tool cover cleaner body (B). OFF position. from handle section. Discard card- board. Remove powered hand tool (some models). Slide handle section onto back Remove switch lock above OFF switch (D) by pulling...
- Page 5 assembled cleaner will look like the drawing. Model with Powered Hand Tool is shown. Cleaner description 1. Handle 20. Hose rack 2. ON/OFF switch 21. Cord hooks: wrap 3. Tool cover cord around hooks storage. hook 4. Dusting brush 5. Powered hand tool* rotated right left...
- Page 6 lllllliili,,i,,,. Handle position Carpet height Settings adjustment ease sliding knob, handle For maximum cleaning performance, should in the upright position (C). following (;arpet height settJn(js cleaning carpet rugs takes recommended. The nozzle will not move into the place nozzle (A), adjusted position until...
- Page 7 Cleaning tools Tools allow cleaning surfaces above floor reaching hard clean areas. Handle must be in the upright posi- tion for tool use. CAUTION: Agitator continues to rotate while cleaner handle is in upright position. Avoid tipping cleaner or How to attach tool setting...
- Page 8 When empty is recommended that dirt Familiarize yourself withthese home emptied before dirt reaches dirt maintenance tasks as[)roper useand 3-1) inlet opening back dirt (Fig, careofyour G leaner will e nsure c ontin- alter every if preferred, uedcleaning e ffectiveness. CAUTION: Very fine materials, such as face powder, cornstarch or fire- place soot, may seal the filter and...
- Page 9 Reposition filter, grill screw. Replace dirt cup. Should want replace this filter, for HOOVER part No. 38762008. filter reposition it on side cleaner. Make sure white side filter faces outward. Close door. Should want...
- Page 10 What strongly recommend check This cleaner uses a 1 2 volt, wedge base debris accumulation under agitator type 912 bulb, HOOVER part No. shield each time clean filters. 27313101. Removing debris under shield will help maintain your cleaner's...
- Page 11 What When purchasing edge groomers, for HOOVER part No. 39511004. to replace Installing groomers Lift both edge groomers slide Disconnect cleaner from electrical outlet. edge groomers into position shown.
- Page 12 (some models only) Agitator brush roll replacement When agitator brush roll brushes worn, brush roll sbould replaced. Ask for HOOVER part No. 48414088. 3. Remove agitator including plates Unscrew Phillips screws remove belt guard (B). discard. Inspect belt ensure that...
- Page 13 Hoover Cleaning bearings that should lubricated • Filter assembly not assembled periodically a Hoover Factory properly Perform ance Service Center Authorized Hoover • Ensure that filter asserrlbly This Hoover Cleaning Performance Sys-...
- Page 14 "Cleaner suction 1. Look (Domestic Use) into hose remove low", blockage. Check lower dirt duct blockage Your HOOVER '_ 4-1). appliance warranted (Fig. normal household use, in accordance Clearing blockages C. If a blockage occurs during powered with Owner's...