Chroma Auto 1 Screen; Chroma Func Screen; Remote Control; Mecha Adj Screen - Kenwood DDX6019 Service Manual

Chroma Auto 1 screen

• After the auto adjustment for Chroma, save the memory
into the E2PROM.
Auto Adjustment items: RGB_Amplitude
Ganma1 Ganma2 CONT_RGB2
SUB_B right_B COM_Amplitude
• E2PROM normal write or abnormal result will display on
the screen.
• EEPROM's Chroma data is not cleared by writing region in.
EEPROM Chroma data is cleared by the [Clear] key on the
Service screen.

Chroma Func screen

• After the Chroma adjustment, save the memory into the
E2PROM.
• Setting operation is done by the remote control.
• Chroma_IC adjustment screen (Item setup)
EEPROM
Setup items: Tint adjustment (00h~FFh)
Phase adjustment (00h~3Fh)
• E2PROM normal write or abnormal result will display on
the screen.
• EEPROM's Chroma data is not cleared by writing region in.
EEPROM Chroma data is cleared by the [Clear] key on the
Service screen.

MECHA ADJ screen

• After the panel mechanism position control, save the
memory into the E2PROM.
• Write the voltage value at when Full Open/Full Close into
E2PROM.
• E2PROM normal write or abnormal result will display on
the screen.
• In one of the conditions below, "NG" is displayed (when NG,
not written into E2PROM).
E2PROM writing-in error.
NG if the voltage acquiring value is 0.177V or higher when
Open.
NG if the voltage acquiring value is lower than 2.746V or
higher than 2.888V when Close.
Source / Audio / Set Up screen
• Source / Audio Control / Set Up screens are same as when
in normal mode.
Display
• Basically, dedicated screen when in Test Mode.
• Display Touch position (+). However, shall not be displayed
in Touch Adjust screen (under adjustment).
TEST MODE
Key
• [Tact] key specification is shown below.
Bright
SRC/Vol Up/Vol Dw/Open (Eject)
SUB_Bright_R
ATT
V.SEL
FNC

Remote control

• Carry out the following operations using NA-R300 (SW:
AUD) (other than the listed blow shall be operated normally).
Direct
Band (FM+)
M/S (AM-)
Write to
Execution
(Play/Pause)
Tenkey 5
Tenkey 6
Tenkey 7
Tenkey 8
Tenkey 9
Tenkey 0
Tenkey 2 (Preset 2)
Tenkey 3 (Preset 3)
Tenkey 4 (Preset 4)
Screen maintenance section
• In Test Mode (including when the jig is connected), start up
in VIDEO screen
Mode Main screen.
• Connect AVOUT to the V.SEL action to allow change
(AVOUT when in Graphic and NAVI can be any).
AVIN – (TV) – R_CAM – NAVI – DVD (the order can be any)
• Easy Control screen is skipped with [FNC] key.
• For the Reverse condition needs to be set ON when in the
test mode (RCAM is always available in V.SEL).
(When detecting Reverse, R-CAM interruption will occur as
is in normal mode).
• When VIDEO image is input and when video signal is
switched (NTSC
displayed when switching V.SEL. However, the OSD is not
displayed in VIDEO mode.)
DDX6019/6029/6029Y/6039
Key
As usual
Driver for motor On
V.SEL+AVOUT (engaged with V.SEL)
As usual (no easy)
Key code
Chroma_IC adjustment mode ON/OFF
(writing-in)
Video mode switching (NAVI/AVIN/DVD)
DVD audio/video confirmation switching
Setup/cancel Chroma setting value
Navi forced interruption
Call Screen adjustment screen
To the item before Chroma adjustment
Change the Chroma setup value (UP)
To the next Chroma adjustment item
Change the Chroma setup value (DW)
DC Offset detection test direct switching
(DVD source only)
Switching the V-IN (R-CAM) mirror mode
Direct switching for HPOSI DVD checking
press the [FNC] key to move on to Test
PAL), OSD is not displayed. (OSD is
Function
Item
19