Modification Of D, E, F, 7 Page Data - Sony CCD-TR618 Service Manual

1-2. INITIALIZATION OF D, E, F, 7 PAGE DATA
1. Initializing the D, E, F, 7 Page Data
Note1: If "Initializing the D, E, F, 7 Page Data" is performed, all data of
the D page, E page, F page and 7 page will be initialized. (It is
impossible to initialize a single page.)
Note2: If the D, E, F, 7 page data has been initialized, "Modification of D,
E, F, 7 Page Data" and all adjustments need to be performed again.
Adjustment page D
Adjustment Address 10 to FF
Adjustment page F
Adjustment Address 10 to FF
Adjustment page E
Adjustment Address 00 to FF
Adjustment page 7
Adjustment Address 00 to FF
Note: NTSC model: CCD-TR618/TR818/TRV49/TRV58/TRV68/
TRV78/TRV88/TRV98
PAL model: CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/
TRV59E/TRV78E/TRV98E
Initializing Method:
Order Page Address Data
1 0 01 01
2 6 00
3 6 01
4 6 02
5 2 00 29
6 2 01 29
7

2. Modification of D, E, F, 7 Page Data

If the D, E, F, 7 page data has been initialized, change the data of
the "Fixed data-2" address shown in the following tables by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Procedure
Set the data.
Set the following data.
55: NTSC model
51: PAL model
Set the following data, and press
PAUSE button.
55: NTSC model
51: PAL model
Check that the data changes to
"01".
Set the data
Set the data, and press PAUSE
button.
Perform "Modification of D, E,
F, 7 Page Data".
Processing after Completing Modification of D, E, F, 7 Page
data
Order Page Address Data
1 2 00
2 2 01
Note: If the following symptoms occur after completing of the
"Modification of D, E, F, 7 page data", check that the data of the
"Fixed data-2" addresses of D page are same as those of the same
model of the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
3. D Page Table
Note1: Fixed data-1: Initialized data. (Refer to "1. Initializing the D, E, F,
7 Page Data".)
Fixed data-1: Modified data. (Refer to "2. Modification of D, E, F,
7 Page Data".)
Initial value
Address
NTSC PAL
00 to 0F
10 00 00
11 to 12
13
14
15
16 to 19
1A
1B to 1E
1F
20
21
22
23
24 to 26
27
28 to 2C
2D
2E
2F
30
31 to 3F
40
41
42
43
44
45
46 to 47
48
49
4A to 4C
4D
4E
4F
50
51
52
5-9
Procedure
29 Set the data
29 Set the data, and press PAUSE
button.
Remark
Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)