Dose Setting - Omega FMG600 Series User Manual

The display will read "[CZ] Czech / [EN] English". To page through the menu items, use push-buttons
(direction downwards) and
menu will appear on the display with the Language option on the first line.
Menu: Production data, depress
The display will read "Sensor number". Using push-button
increase/decrease the selected figure by push-buttons
series number (maximum 10 digits). Depress
any key, preferably . The Production data menu will reappear on the display with the Sensor Number item
selected.
Menu: Production data, depress
The display will read "Sensor DN". Using push-button
increase/decrease the selected figure by push-buttons
(maximum 10 digits). Depress
preferably . The Production data menu will reappear on the display with the Sensor DN item selected.
Menu: Production data, depress
The display will read „1: Error EEPROM, 2: Overflow OUT1". Scrolling in menu is possible using push-
buttons (down) and
With buttons and
another error. When finished, depress
Menu: Production data, depress
The display will read "Dose Correction xxxxx". The value specified here will be added or subtracted from the
earlier specified dose size. Move the cursor by repeated actuation of push-button
value by push-buttons
representing the dose correction in the given volume units. Confirm your selection by depressing
display will read "Value Entered Press Any Key". Depress
menu, item "Dose Correction".
Menu: Production data, depress
The first display line will show "A → B", the second line "A ↔ B". The first line applies. Select the correct
information by push-button
Depress . The Production Data menu will appear on the display with the "Flow Direction" item selected.
Menu: Production data, depress
The display will read "Base Frequency LXXX". Move the cursor by repeated depressing of push-button
and set the desired value by push-buttons
figure equal to the base frequency in Hz specified in the table shown in section 7.1.4. Then depress
display will read "Value Entered Press Any Key". Depress
menu, item "Base frequency".
To return to the basic programming menu, item "Production data", depress push-button

7.1.8. Dose setting

The dosing mode is operational provided the Display item is selected from the "Displayed Data" menu. The
dosing mode allows for measurement of the preset fluid volume (dose). The external initiation command
shall be brought to the input of optocoupler IN1. As soon as the preset dose has passed through the meter
probe, the output optocoupler (OUT3) will close. The dosing process will be repeated with every new
external initiation signal brought to the input of optocoupler IN1. Depress push-button
dosing process currently in progress. Following that, the next dosing process can be initiated at any time.
Menu: Dose setting, depress
The display will read "Dose Size xxxxx". Using push-button
position and increase/decrease the selected figure by push-buttons
a number equal to the dose size. Depress
Design, Assembly and Service Manual
Induction flow meter FMG600 series
(upwards). Select the desired language and depress
/ Sensor number, depress
/ Sensor DN, depress
. The display will read "Value entered Press any key". Press any key,
/ Errors, depress
(up). Scroll to desired error and depress
set desired error feature and depress
and return to item "Errors".
, Dose correction, depress
and (increase/decrease). The five "x" should be replaced by a figure
/ Flow direction, depress
, then depress
/ Base frequency, depress
and
. The display will read "Value Entered Press Any Key". Press
move the cursor to the desired position and
and , respectively. Enter the sensor production
. The display will read "Value entered Press any key". Press
move the cursor to the desired position and
and , respectively. Enter the sensor dimension
. Display will read „Active, Non-active".
. Then you can continue with setting of
. This takes you back to the Production Data
. The display will read "Value Entered Press Any Key".
(increase/decrease). The X-es should be replaced by a
. This takes you back to the Production Data
move the cursor to the desired decimal
and
Page 39 of 44
. The Production data
, and set the desired
.
to discontinue the
, respectively. Replace xxxx by
. The
,
. The