Standard Horizon CP150 Owner's Manual page 74

Time Line
Disables (Off) or sets Time Line as 2, 10, 30 min, 1, 2 hours, Infinite.
The Time Line is the graphical indicating of the direction in which the vessel is heading toward. The
Time Line starts from the vessel position icon. Its angle is given by the value of COG and its length
is proportional to the SOG. When the Time Line is set to Infinite the line always reaches the screen
frame. When the Destination is set on DSC position, if the current setting of Time line is Off, it must
be automatically changed to Infinite.
The default setting is Infinite.
'MENU' + "GENERAL SETUP" + 'ENTER' + "TIME LINE" + 'ENTER'
Time Reference
Sets UTC or Local Time. The default setting is UTC.
'MENU' + "GENERAL SETUP" + 'ENTER' + "TIME REFERENCE" + 'ENTER'
Time (Track)
When the tracking function is On and the type of Track storing is Time, the chartplotter can store a fix
after a defined time. Choose among 1, 5, 10, 30 sec, 1, 5, 10 min. The default setting is 1 sec.
'MENU' + "TRACK" + 'ENTER' + "TIME" + 'ENTER'
Track (menu)
The chartplotter stores all points in its memory. The chartplotter can store a fix when the distance from
its last stored position is greater than a defined distance or after a defined time. A line connects such
points and represents the past course, called the Track of the ship.
Active Track selecting: 'MENU' + "TRACK" + 'ENTER' + "ACTIVE TRK" + 'ENTER'
Track storing ON/OFF: 'MENU' + "TRACK" + 'ENTER' + "TRACKING" + 'ENTER'
Visible ON/OFF: 'MENU' + "TRACK" + 'ENTER' + "VISIBLE" + 'ENTER'
Step unit selection: 'MENU' + "TRACK" + 'ENTER' + "STEP UNIT" + 'ENTER'
Deleting Track : 'MENU' + "TRACK" + 'ENTER' + "CLEAR" + 'ENTER' + "YES" + 'ENTER'
Track line pattern selecting: 'MENU' + "TRACK" + 'ENTER' + "LINE PATTERN" + 'ENTER'
Tracking
Turns On/Off the Track storing. It is not possible to use the Track storing if you are not receiving a valid
fix. The default setting is On.
'MENU' + "TRACK" + 'ENTER' + "TRACKING" + 'ENTER'
Tracks & Routes
Turns On/Off the displaying of Tracks and Routes (recommended and established Routes for ships
at sea, including traffic separation schemes, deep water Routes, ...). The default setting is On.
'MENU' + "MAP SETUP" + 'ENTER' + "NAV AIDS SETTINGS" + 'ENTER' + "TRACKS & ROUTES" + 'ENTER'
TRN = Turning
The difference between COG and BRG. If COG is 80° and BRG is 75°, TRN is 5° Left.
TTG = Time To Go
The estimated time needed to reach your destination, based on your current speed and the distance
to destination.
Underwater Objects
Turns On/Off the displaying of Underwater Objects. (Diffuser, Obstruction, Wreck, Cable - submarine,
Cable area, Pipeline area, Pipeline - submarine/on land. The default setting is On.
'MENU' + "MAP SETUP" + 'ENTER' + "NAV AIDS SETTINGS" + 'ENTER' + "UNDERWATER OBJECTS" +
'ENTER'
Unit of Measure (menu)
Sets the units for Distance, Speed, Depth and Altitude.
'MENU' + "GENERAL SETUP" + 'ENTER' + "UNITS OF MEASURE" + 'ENTER'
User C-CARD
The chartplotter uses the optional user C-CARD to save user data: it is a convenient medium to store
and retrieve your information. Before a new user C-CARD can be used, you must format it. The
formatting function initializes the user C-CARD and prepares it for storing information. Remember that
if an user C-CARD is not blank, formatting it will destroy any data already present on the user C-CARD
(the user C-CARDs must be formatted in order to be reused, this operation means all old data
memorized on the user C-CARD will be lost). Data stored on user C-CARD are grouped in files.
Select USER C-CARD menu: 'MENU' + "USER C-CARD" + 'ENTER'
User Point
Place on the chart identified by its coordinates and displayed on the screen with a reference symbol
(see Mark, Waypoint).
Page 76 GPS Chart 150