Rear Panel Connections And Controls - Extron electronics DVI-RGB 150 User Manual

Installation and Operation, cont'd
7. Slide the device in or out until it is in the desired position.
Tighten the screws installed in step 2.
If the screws are inaccessible to a screwdriver:
a. Mark the location of the brackets relative to the screws.
b. Remove the transmitter or receiver from inside the
furniture.
c. Tighten the screws.
d. Replace the unit inside the surface (step 6).

Rear Panel Connections and Controls

a
Input connector — Connect a single link of direct digital video
to this 25-pin DVI-D connector (fi gure 2-5) using the included
cable.
100-240 50/60 Hz
DVI-RGB 150
INPUT
0.35A MAX
7 1
Figure 2-5 — DVI-RGB 150 rear panel
b
Buffered Loop-through connector — If desired, connect a direct
digital local monitor to this 25-pin DVI-D connector.
c
Output connectors — Connect an RGB display to these female
BNC connectors.
For RGBHV video — Connect to fi ve
BNC connectors as shown at right.
Ensure that the SOG On/Off switch
is turned off.
For RGBS video — Connect to four BNC
connectors as shown at right. Ensure that
the SOG On/Off switch
For RGsB video — Connect to three BNC
connectors as shown at right. Ensure that
the SOG On/Off switch
2-6 DVI-RGB 150 • Installation and Operation
R G B
DDC
BUFFERED
HIGH
OUTPUT
SOURCE
LOOP-THROUGH RESOL. H V S
MONITOR
SELECTOR
LOW OUTPUT
2 4 6 5 3
R G
H V
f
( )
R G
f
( ) is turned off.
H V
f
(
) is turned on.
R G
H V
B
S
B
S
B
S
d
DDC Source switch — Set this switch to the Monitor (up)
position to connect the DDC channel between the direct
digital video source and the local monitor.
Set this switch to the Selector (down) position to connect
the DDC channel between the direct digital video source
and the built-in DVI-RGB 150 DDC logic.
e
Output Resolution rotary switch — If the DDC Source
d
(
switch ) is in the Selector position, set this switch to the
appropriate position to select the desired video resolution.
f
(
Use the Refresh DIP switch
rate. The table below identifi es the switch positions and the
associated resolutions and vertical refresh rates.
Output Resol. Refresh
Switch DIP Switch
< >
Pos. Resolution Pos. Resolution
Dwn Up
0 640x480 60 Hz 75
1 800x600 60 Hz 75
2 852x480 60 Hz 75
3 1024x768 60 Hz 75
4 1024x852 60 Hz 75
5 1280x768 60 Hz 75
6 1280x1024 60 Hz 75
7 1365x768 60 Hz 75
N
Many monitors will not support all of the resolutions and
refresh rates shown. If you get no display, try a different
rate.
f
SOG (Sync on Green) On/Off switch— Set this switch to
the On (up) position to enable SOG for RGsB video. Set
this switch to the Off (down) position to disable SOG for
RGBS or RGBHV video.
Refresh switch — If the DDC Source switch
Selector position, set this switch either up or down to select
the refresh rate of the selected output. See the table above.
g
AC power connector — Plug a standard IEC power cord
into this connector to connect the interface to a 100 to 240VAC,
50 Hz or 60 Hz power source.
DVI-RGB 150 • Installation and Operation
DDC
SOURCE
MONITOR
SELECTOR
OUTPUT
RESOL.
) to select the refresh
Output Resol. Refresh
Switch DIP Switch
< >
Dwn Up
8 1366x768 60 Hz 75
9 1400x1050 60 Hz 60
A 1600x1200 60 Hz 60
B 480p 60 Hz 60
C 576p 50 Hz 50
D 720p 50 Hz 60
E 1080i 50 Hz 60
F 1080p 50 Hz 60
HIGH
d
LOW
( ) is in the
2-7