Sony DVP-CX777ES Service Manual page 111

Pin No. Pin Name
119 IOVSS06
120
SDAD11O
SDCS0ON,
121, 122
SDCS1ON
123 IOVDD07
124 SDCKEO
125 SDRASON
126 IOVSS07
127 SDCLKO
128 IOVDD08
129 SDCASON
130 SDWEON
131 CVS06
SDDQM0O,
132, 133
SDDQM1O
134 IOVSS08
135 to 138
SDDQ6 to SDDQ9
139 CVD06
SDDQ4, SDDQ5,
140 to 143
SDDQ10,
SDDQ11
144 IOVDD09
SDDQ2, SDDQ5,
145 to 148
SDDQ12,
SDDQ13
149 IOVSS09
150, 151
SDDQ1, SDDQ14
152 IOVDD10
153, 154
SDDQ0, SDDQ15
155 IOVSS10
156 CRPCLKI
157 TESTI
158 CLKI
159 PAVDD18P
160 SCLKI
161 PAVSS18G
162 MBIST_EN
163 SCAN_MOD
164 SCAN_EN
165 IOVDD11
166, 167
HAD22I, HAD23I
168, 169
HAD20I, HAD21I
170 CVS07
171 to 174
HAD16I to HAD19I
175 IOVSS11
176 to 179
HAD12I to HAD15I
180 CVD07
181 to 184
HAD8I to HAD11I
185 IOVDD12
I/O
—
Ground terminal (for digital system)
O
Address signal output to the SD-RAM
O
Chip select signal output to the SD-RAM
— Power supply terminal (+3.3V) (for digital system)
O
Clock enable signal output to the SD-RAM
O
Row address strobe signal output to the SD-RAM
—
Ground terminal (for digital system)
O Clock (108 MHz) signal output to the SD-RAM
—
Power supply terminal (+3.3V) (for digital system)
O
Column address strobe signal output to the SD-RAM
O
Write enable signal output to the SD-RAM
— Ground terminal (for digital system)
O
DQM signal output to the SD-RAM
—
Ground terminal (for digital system)
I/O
Two-way data bus with the SD-RAM
—
Power supply terminal (+1.8V) (for digital system)
I/O
Two-way data bus with the SD-RAM
—
Power supply terminal (+3.3V) (for digital system)
I/O
Two-way data bus with the SD-RAM
—
Ground terminal (for digital system)
I/O
Two-way data bus with the SD-RAM
—
Power supply terminal (+3.3V) (for digital system)
I/O
Two-way data bus with the SD-RAM
—
Ground terminal (for digital system)
I
Not used
I
Input terminal for the test (normally: fixed at "H")
I
Clock (27 MHz) signal input from the clock generator
—
Power supply terminal (+3.3V) (for analog system)
I System clock (27 MHz) signal input from the clock generator
I
Ground terminal (for analog system)
I
Not used
I
Not used
I Not used
—
Power supply terminal (+3.3V) (for digital system)
I
Chip select signal input from the system controller
I
Address signal input terminal
— Ground terminal (for digital system)
I
Address signal input terminal
—
Ground terminal (for digital system)
I
Address signal input terminal
— Power supply terminal (+1.8V) (for digital system)
I
Address signal input terminal
—
Power supply terminal (+3.3V) (for digital system)
Description
DVP-CX777ES
111