Frequency Addition Function (A145, A046, C001 To C008); Start/End Frequency Setting For External Analog Input - Hitachi SJ700-2 Instruction Manual

Chapter 4 Explanation of Functions
4.2.13 Frequency addition function
The frequency addition function allows you to add or subtract the
value specified as the frequency to be added (A145) to or from the
frequency value of a selected frequency command.
To use this function, assign function "50" (ADD) to an intelligent input terminal.
When the ADD terminal is turned on, the inverter performs the addition or subtraction of the value specified
as "A145".
Item
Frequency to be added
Selection of the sign of the
frequency to be added
Terminal function
Note 1: If the sign of the frequency value in the frequency command changes from minus (-) to plus (+), or
vice versa, as the result of frequency addition, the motor operation direction will be inverted.
Note 2: When the PID function is used, the frequency addition function can apply to PID target data. (In
such cases, the data display by function "A145" is in percentage [in steps of 0.01%]).

4.2.14 Start/end frequency setting for external analog input

The start/end frequency setting function
allows you to set the inverter output
frequency in relation to the external analog
inputs (frequency commands) via the
following terminals:
O-L terminal: 0 to 10 V
OI-L terminal: 4 to 20 mA
O2-L terminal: -10 to +10 V
(1) Start/end frequency settings for the O-L and OI-L terminals
Item
[O]/[OI]-[L] input active
range start frequency
[O]/[OI]-[L] input active
range end frequency
[O]/[OI]-[L] input active
range start voltage
[O]/[OI]-[L] input active
range end voltage
[O]/[OI]-[L] input start
frequency enable
If the voltage of the signal to be input to the O-L terminal is 0 to 5 V, specify 50% for "A014".
(Example 1) A015/A105: 00
Maximum
frequency
A012/A102
A011/A101
0 A013/A103 A014/A104
(0 V/0 mA)
Function code
A145
A146
C001 to C008
A011: [O]-[L] input active range start frequency
A012: [O]-[L] input active range end frequency
A013: [O]-[L] input active range start voltage
A014: [O]-[L] input active range end voltage
A015: [O]-[L] input start frequency enable
A101: [OI]-[L] input active range start frequency
A102: [OI]-[L] input active range end frequency
Function code Range of data
0.00 to
A011/A101
400.0(Hz)
0.00 to
A012/A102
400.0(Hz)
A013/A103 0. to 100.(%)
A014/A104 0. to 100.(%)
00
A015/A105
01
Out put frequency in
the range from 0% to
A013/A103 is
A011/A101
Analog input
100%
(10 V/20 mA) (O/OI)
Data or range of data
0.00 to 400.00(Hz)
00
01
50
Related code
Setting of the start frequency
Setting of the end frequency
Setting of the rate of the start frequency to the
external frequency command (0 to 10 V/0 to 20 mA)
Setting of the rate of the end frequency to the
external frequency command (0 to 10 V/0 to 20 mA)
Externally input start frequency
The frequency set as "A011" or "A101" is output as
the output frequency while the start-frequency rate is
0% to the value set as "A013" or "A103".
0 Hz
0 Hz is output as the output frequency while the
start-frequency rate is 0% to the value set as "A013"
or "A103".
(Example 2) A015/A105: 01
Maximum
frequency
A012/A102
A011/A101
0 A013/A103 A014/A104 100%
(0 V/0 mA)
4 - 14
Related code
A145: Frequency to be added
A146: Sign of the frequency to be added
C001 to C008: Terminal [1] to [8]functions
Description
Setting of the frequency to be added
(Frequency command) + (A145)
(Frequency command) - (A145)
ADD selection of the trigger for adding
the frequency (A145)
A103: [OI]-[L] input active range start current
A104: [OI]-[L] input active range end current
A105: [OI]-[L] input start frequency enable
A111: [O2]-[L] input active range start frequency
A112: [O2]-[L] input active range end frequency
A113: [O2]-[L] input active range start voltage
A114: [O2]-[L] input active range end voltage
Description
(10 V/20 mA)
Out put frequency in
the range from 0% to
A013/A103 is 0Hz
Analog input
(O/OI)