Quick Memory; Storing Into Quick Memory; Recalling Quick Memory Channels; Temporary Frequency Changes - Kenwood TS-480HX Instruction Manual

QUICK MEMORY

Quick Memory is designed to quickly and temporarily
save data without specifying a particular memory
channel. Use Quick Memory to store data you will
not use in future operating sessions. For example, as
you tune across the band looking for DX, it is
convenient to store stations that you want to contact.
You can quickly jump between several different
memory channels as you monitor them.
This transceiver provides 10 Quick Memory channels
("0_" to "9_") that can store the following data:
V F O A f e r q u e n y c a n d
o p r e t a n i g m o d e
R T I O / N O F F
I R / T X T I f o s f e f t e r q u e n
N o s i e B a l n k r e O / N O F
D S P N o s i e R e d u t c o i n
O F / F / 1 2
D g i t i l a N o s i e i L m t i r e
O F / F 1 ~ 3

STORING INTO QUICK MEMORY

Each time you store a new frequency, all previously
stored frequencies are bumped to the next respective
Quick Memory channel. When all 10 memory
channels contain frequencies, storing one more
frequency bumps the contents of memory channel 9
off the stack (the data is lost).
The following diagram illustrates how the Quick
Memory stacks the data in memory each time you
press [QMI/ M.IN].
New data
24.911 14.005
Memory 0 Memory 1 Memory 2
50.015 7.082
Memory 5 Memory 6 Memory 7
New data
21.005 24.911
Memory 0 Memory 1 Memory 2
18.111 50.015
Memory 5 Memory 6 Memory 7
New data
14.085 21.005
Memory 0 Memory 1 Memory 2
14.250 18.111
Memory 5 Memory 6 Memory 7
You can store data in the Quick Memory only when
you operate the transceiver in VFO mode.
1 Select the frequency, mode, etc. on the
transceiver VFO.
2 Press [QMI/ M.IN].
V F O B f e r q u e n y c
o p r e t a n i g m o d e
X T I O / N O F F
y c D S P t l i f r e b a n d w d i
F F N I E O / N O F F
D S P B e t a C a n c
O F / F / 1 2
T / X R X u f n t c o i n
14.235 21.250 18.111
Memory 3 Memory 4
29.610 3.545 14.195
Memory 8 Memory 9
14.005 14.235 14.250
Memory 3 Memory 4
7.082 29.610 3.545
Memory 8 Memory 9
24.911 14.005 14.235
Memory 3 Memory 4
50.015 7.082 29.610
Memory 8 Memory 9
• Each time [QMI/ M.IN] is pressed, the current
VFO data is written to the Quick Memory.
When RIT or XIT is ON, this ON status and the offset will
Note:
also be stored.

RECALLING QUICK MEMORY CHANNELS

You can recall a Quick Memory channel only when
you operate the transceiver in VFO mode.
1 Press [QMR/ Ms s s s s VFO].
• The current memory channel number appears.
a n d
• If there is no data stored in any Quick Memory
channel, the data cannot be recalled to the
h t
current VFO, an error beep sounds.
2 Turn the MULTI control to select a Quick Memory
channel (0 to 9).
l e • You cannot change memory channels while
transmitting.
3 To exit, press [QMR/ Ms s s s s VFO] again.
s
Memory channels cannot be changed while using the
Note:
TF-SET function.

TEMPORARY FREQUENCY CHANGES

After recalling a Quick Memory channel, you can
temporarily change the data without overwriting the
contents of the channel. You can change the
frequency even when you select "oFF" in Menu
No. 07.
1 Press [QMR/ Ms s s s s VFO].
2 Turn the MULTI control to select a Quick Memory
channel (0_ to 9_).
3 Change the frequencies and associated data.
4 To store the changed data in the Quick Memory,
press [QMI/ M.IN].
• This action stores the new data in the current
channel and bumps the old frequency to the
next higher Quick Memory channel.
5 To exit, press [QMR/ Ms s s s s VFO] again.
Memory channel data can also be changed while using
Note:
the TF-SET function.
QUICK MEMORY ➡ VFO TRANSFER
This function copies the contents of the recalled
memory channel to the VFO.
1 Recall a Quick Memory channel.
2 Press [QMR/ Ms s s s s VFO] (1 s).
Note: Pressing
recalled data copies the new data to the VFO.
11 MEMORY FEATURES
[QMR/ M s s s s s VFO]
after temporarily changing the
55