Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planar PT2245PW
Summary of Contents for Planar PT2245PW
- Page 1 PT2245PW Touch Screen Monitor USER’S GUIDE www.planar.com...
- Page 2 Any changes or modifications to this TFT LCD would void the user’s authority to operate this device. For more information on how to recycle your product, please visit WWW.PLANAR.COM/GREEN.
-
Page 3: Table Of Contents
Table of Contents Usage Notice Precautions ......................... 1 Introduction About PT2245PW Series ..................... 2 Touch Screen for PT2245PW ..................2 Package Overview ...................... 3 Installation Product Overview ......................4 Front View ....................... 4 Bottom View (Without Stand) .................. 4 VESA Mount for Your Monitor ..................5 Start Your Installation .................... -
Page 4: Usage Notice
Usage Notice Warning - To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. -
Page 5: Introduction
Introduction About PT2245PW Series The PT2245PW Series is a 21.5" flat panel screen with an active matrix, thin-film transistor (TFT) edge-lit LED LCD. This unit is to be used as commercial and light industrial equipment only. Features include: • Direct Analog signal input •... -
Page 6: Package Overview
Package Overview LCD Display Power Cord VGA Signal Cable USB Cable ( A to B) DVI-D Cable DC Power Supply User’s Guide Landing Strip Cable Cover Screw... -
Page 7: Installation
Installation Product Overview • Front View • Bottom View (Without Stand) DC IN RJ-Type... -
Page 8: Vesa Mount For Your Monitor
VESA Mount for Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors, and corresponding with the standards of flat panel monitor mounting devices, such as wall and table arms. -
Page 9: Start Your Installation
Start Your Installation Please follow these instructions so that you can hook up the cables to associated connectors. 1. Lay the display flat on an even surface. 2. Move the stand into position as seen in the step 1 diagram. 3. -
Page 10: Connecting The Display (Figure 8.1)
Connecting the Display (Figure 8.1) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC plug to the power connector on the monitor and the other end into an electrical outlet (8.1). -
Page 11: (Figure 8.1)
(Figure 8.1) (Optional) -
Page 12: User Controls
User Controls Side Panel Controls Icon Key Name Menu Down Select Power Menu off status Menu on status Menu appear Menu disappear / return to main item Brightness Main item select up / Adjust up Contrast Main item select down / Adjust down Select sub-item function Power On / Off... -
Page 13: How To Use The Osd Menus
How to Use the OSD Menus Icon Key Name Menu Down Select Power 1. Press the “Menu” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the five functions in the main menu. 2. -
Page 14: On-Screen Display Menus
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically. Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. -
Page 15: Appendix
Appendix Troubleshooting If you are experiencing trouble with the display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected as described in the “Installation”... -
Page 16: Warning Signal
Warning Signal If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card. Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or our service center for more information. -
Page 17: Product Dimensions
Product Dimensions 517.4 mm ► Front View 46.0 mm ► Side View 249.6 mm ► Top View... - Page 18 Rotate 313.3 mm ► Front View 46.0 mm ► Side View 249.6 mm ► Top View...
-
Page 19: Compatibility Modes
Compatibility Modes Mode Resolution H-Frequency(khz) V-Frequency(hz) IBM VGA 720X400 31.47 IBM VGA 640X480 31.47 Apple MacII 640X480 35.00 VESA VGA 640X480 37.86 VESA VGA 640X480 37.50 VESA SVGA 800X600 35.16 VESA SVGA 800X600 37.88 VESA SVGA 800X600 48.08 VESA SVGA 800X600 46.88 Apple Mac... -
Page 20: Touch Screen Driver Installation
A calibration tool can be installed for improved touch position accuracy. See “Optional Calibration Tool Install” section for more information. 2. For PT2245PW, the system requires 15 seconds for Windows 7/8 to process the touch program while turning power on/off or plugging/unplugging USB cable. -
Page 21: Pt2245Pw Calibration Instruction
PT2245PW Calibration Instruction: Calibrating the touch screen in Windows 7/8: 1. Tap the Start button, Control Panel and then Hardware and Sound. 2. Under Tablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Yes to allow the program to make changes. -
Page 23: Pt2245Pw Install Instruction
3. Be sure that your EWF is disabled. If your EWF is enabled, please disable the EWF by using the EWF Manager command. 4. Once the EWF is disabled click on the XP driver at www.planar.com/support. and follow the step-by-step instructions as shown on the pop-up windows. -
Page 24: Technical Support
Technical Support Cables and Accessories To find cables and accessories for your Planar monitor, touch screen or other Planar products visit our online store at www.PlanarOnline.com. Technical Support Visit Planar at http://www.planar.com/support for operations manuals, touchscreen drivers, warranty information and access to Planar’s Technical Library for online trouble shooting. - Page 25 Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day, 7 days a week © 2013 Planar Systems, Inc. 10/13 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners.