The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission.
Usage Notice Warning - To prevent the risk of fi re or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.
Introduction About PT1945R/PT1945RW/PT1945S The PT1945R/PT1945RW/PT1945S is a 19" fl at panel screen with an active matrix, thin-fi lm transistor (TFT) liquid crystal display (LCD). Features include: • Direct Analog signal input • Active matrix TFT LCD technology • PT1945R/S - 1280 x 1024 SXGA resolution •...
Package Overview LCD Display VGA Signal Cable Power Cord Audio-in Cable USB Cable ( A to B) RS-232 Cable DC Power Supply Touch Screen Driver Landing Strip Installation CD-ROM (for PT1945RW only) User’s Guide Screw...
Installation Product Overview • Front View PT1945R/PT1945S PT1945RW • PT1945R/PT1945S Bottom View AUDIO AC IN RS-232 POWER SWITCH • PT1945RW Bottom View RS-232 DC IN AUDIO EARPHONE POWER SWITCH...
5. Position all cables under the cover lip as seen in the step 5 diagram. 6. Re-attach the cable cover . Remove the screw (CBM M3x6) from the accessory box, and insert the screw into the cable cover and monitor as seen in the step 5 diagram. PT1945R/PT1945S Step 2 Step 2...
Connecting the Display (Figure 8.1) To setup this display, please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (8.1).
Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included. PT1945R/PT1945S PT1945RW...
To mount the monitor on an UL-listed certifi ed swing arm or other mounting fi xture, follow the instructions included with the mounting fi xture to be used. PT1945R/PT1945S Slots (x4) 100.0 mm...
User Controls Side Panel Controls PT1945R/PT1945S Icon key Name Menu Down Enter Power PT1945RW Icon key Name Menu Down Enter Power Menu off status Menu on status Menu appear Menu disappear/ return to main item Brightness Main item select up/ Adjust up...
How to Use the OSD Menus Icon Key Name Menu Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT The monitor luminance level control. Contrast The monitor backlight level control. Brightness Fine-tune the image to full screen automatically. Auto Adjust Moving screen image horizontal position to left or right. Left/Right Moving screen image vertical position to up or down. Up/Down The screen image horizontal dot clock adjustment.
► Reconfi gure the resolution of your computer to make it less than or equal to 1280 x 1024 for PT1945R/S. ► Reconfi gure the resolution of your computer to make it less than or equal to 1366 x 768 for PT1945RW.
Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or Planar for more information. No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card.
PT1945RW Mode Resolution H-Frequency (KHz) V-Frequency (Hz) IBM VGA 720X400 31.47 IBM VGA 640X480 31.47 Apple MacII 640X480 35.00 VESA VGA 640X480 37.86 VESA VGA 640X480 37.50 VESA VGA 800X600 35.16 VESA VGA 800X600 37.88 VESA VGA 800X600 48.08 VESA VGA 800X600 46.88 Apple Mac...
Touch Screen Driver Installation The PT1945R/PT1945RW/PT1945S is available with both RS232 and USB connections. The ® touch driver is located on the enclosed CD-ROM for these operating systems: Windows ® VISTA, XP, 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux, Apple Mac OS.
PT1945R/PT1945RW/PT1945S Install Instructions: ® If you are using a PC running Windows 7, VISTA, XP, 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display.
Page 26
® If you are using a PC running Windows CE, follow the instructions below: 1. Power on the computer. 2. Make sure that the RS232 or USB cable is connected to the computer. 3. Using Platform Builder, build an image fi le by following the step-by-step instructions found in the zipped fi...
Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefi ts of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html.