2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Page 2 For technical questions, please call 1-800-444-3353. Item 69696...
A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Item 69696 For technical questions, please call 1-800-444-3353. Page 3...
RATED SPEED can break and fly apart. the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. Page 4 For technical questions, please call 1-800-444-3353. Item 69696...
Page 5
25. The warnings, precautions, and instructions If unreadable or missing, contact discussed in this instruction manual cannot Harbor Freight Tools for a replacement. cover all possible conditions and situations that may occur. It must be understood by the 17. Avoid unintentional starting.
7. To reduce vibration, maintain the tool as tingling, numbness, and white or blue fingers), explained in this manual. If any abnormal seek medical advice as soon as possible. vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. Page 6 For technical questions, please call 1-800-444-3353. Item 69696...
Page 7
National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Outlets for 2-Prong Plug Item 69696 For technical questions, please call 1-800-444-3353. Page 7...
No Load Revolutions per Minute (RPM) Specifications Electrical Rating 120V~ / 60Hz / 10A No Load Speed 1,500 - 4,000 RPM Spindle Thread 5/8″ x 11 TPI Max. Accessory Diameter 7″ (178 mm) Page 8 For technical questions, please call 1-800-444-3353. Item 69696...
Page 9
Bolt on the long side of the D-Handle. Functions D-Handle Power Spindle Switch Lock Speed Control Panel Display (see detail, right) Decelerate Accelerate Backing Speed is displayed in 100 RPM increments. Example: 25 means 2500 RPM. Item 69696 For technical questions, please call 1-800-444-3353. Page 9...
5. Use the buttons on the control panel Otherwise, damage may occur to the paint to adjust the speed as desired. being polished. Harbor Freight Tools is not responsible for damage to the vehicle’s 6. Keep pressure off of the tool when operating.
Page 11
5. Use the buttons on the control panel Unplug the tool. Clean, then store the to adjust the speed as desired. tool indoors out of children’s reach. Item 69696 For technical questions, please call 1-800-444-3353. Page 11...
WARNING! If the supply cord of this using dry compressed air. Wear ANSI-approved power tool is damaged, it must be replaced safety goggles and NIOSH-approved only by a qualified service technician. breathing protection while doing this. Page 12 For technical questions, please call 1-800-444-3353. Item 69696...
Use only proper type of disc accessory in good condition. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 69696 For technical questions, please call 1-800-444-3353. Page 13...
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 14 For technical questions, please call 1-800-444-3353. Item 69696...
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.