Roland VIMA JM-8 Owner's Manual page 113

FROM NOTE (0 C-~127 G9)
This parameter is only displayed if "DATA TYPE" (see above)
is set to "Note". It allows you to set the note (or lower limit
of the note range) to be modified within the specified
FROM/TO time range.
It is not displayed when you select "EQUAL", "UNEQUAL",
"HIGHER" or "LOWER". See also "Fine-tuning the setting
range".
TO NOTE (0 C-~127 G9)
This parameter allows you to set the upper limit of the note
range to be modified within the specified FROM/TO time
range.
FROM CC (0~127)
This parameter is only displayed if "DATA TYPE" (see above)
is set to something else than "Note". It allows you to set the
lower limit of the control change numbers or values to be
modified within the specified FROM/TO time range.
It is not displayed when you select "EQUAL", "UNEQUAL",
"HIGHER" or "LOWER".
TO CC (0~127)
This parameter allows you to set the upper limit of the con-
trol change numbers or values to be modified within the
specified FROM/TO time range.
Fine-tuning the setting range
Before setting "TO NOTE" (and possibly "FROM NOTE") or
"TO CC" (and possibly "FROM CC"), it might be a good idea
to decide how you want to use the note or value indica-
tions.
Option Meaning
[EQUAL]
Only the selected note or value will change.
(The note/value can be set using the TO
NOTE/TO CC field.)
[UNEQUAL]
All notes or values except the one you
select will change. (The note/value can be
set using the TO NOTE/TO CC field.)
[HIGHER]
Only notes or values above the selected
one will change. (The note/value can be set
using the THAN NOTE/THAN CC field.)
[LOWER]
Only notes or values below the selected
one will change. (The note/value can be set
using the THAN NOTE/THAN CC field.)
[INSIDE]
Only notes or values between FROM NOTE/
FROM CC and TO NOTE/TO CC will change.
[OUTSIDE]
Only notes or values below FROM NOTE/
FROM CC and above TO NOTE/TO CC will
change.
ENTER
Press this display button to confirm your settings and edit
the data.
DELETE
Unlike the "ERASE" function, "DELETE" not only erases
the data but also the measures, beats and/or CPT
units, so that all data that lie behind the "TO" position
are shifted towards the beginning of the track(s). For
this reason, you cannot choose the data type to be
erased.
Delete From 2.1.0 To 4.1.0
TRACK (ALL, 1~16)
Allows you to select the track you wish to edit. You can
also select "ALL" here, in which case the operation applies
to all tracks.
FROM
BAR (1~[last measure of the track or song])—Refers to
the first measure to be edited. By default, the "FROM"
value is set to the beginning of the selected track(s).
BEAT (1~[number of beats per bar])—Specifies the
beat position. The number of available beats depends on
the time signature in the selected area.
CPT (1~119)—Refers to the starting CPT position. "CPT"
is short for "Clock Pulse Time", the smallest unit used by
the JM-8. (There are 120 CPT units to every beat of a 4/4
bar.) Change this setting only if your edit operation
should start after the selected beat.
TO
By default, the "TO" position is set to the last event of the
selected track (or the last event of the longest track when
you select "ALL").
BAR (1~[last measure of the track or song])—This is
where you specify the bar position of the last measure to
be edited.
BEAT (1~[number of beats per bar])—Specifies the
beat position. The number of available beats depends on
the time signature in the selected area.
CPT (1~119)—Refers to the last clock that should be
affected by the edit operation. Change this setting only
if your edit operation should not end exactly on the
selected beat.
ENTER
Press this display button to confirm your settings and edit
the data.
r
VIMA JM-8
Editing 16-track songs
113