D-Link DSR-150 User Manual page 263

Unified Services Router
Wakingup due to wow signal
%s, wowStatus = 0x%x, __func__,
wowStatus
Pattern added already
Error : All the %d pattern are in use.
Cannot add a new pattern ,
MAX_NUM_PATTERN
Pattern added to entry %d ,i
Remove wake up pattern
mask = %p pat =
%p ,maskBytes,patternBytes
mask = %x pat =
%x ,(u_int32_t)maskBytes,
(u_int32_t)patternBytes
Pattern Removed from entry %d ,i
Error : Pattern not found
PPM STATE ILLEGAL %x %x,
forcePpmStateCur, afp->forceState
FORCE_PPM %4d %6.6x %8.8x %8.8x
%8.8x %3.3x %4.4x,
failed to allocate tx descriptors: %d,
error
failed to allocate beacon descripotrs:
%d, error
failed to allocate UAPSD descripotrs:
%d, error
hal qnum %u out of range, max %u!,
HAL AC %u out of range, max %zu!,
HAL AC %u out of range, max %zu!,
%s: unable to update hardware queue
%u!,
Multicast Q:
%p , buf
buf flags - 0x%08x --------- , buf-
>bf_flags
buf status - 0x%08x, buf->bf_status
# frames in aggr - %d, length of
aggregate - %d, length of frame - %d,
sequence number - %d, tidno - %d,
isdata: %d isaggr: %d isampdu: %d ht:
%d isretried: %d isxretried: %d
shpreamble: %d isbar: %d ispspoll: %d
aggrburst: %d calcairtime: %d
qosnulleosp: %d,
%p: 0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x,
0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x 0x%08x
>ifName
DEBUG unable to register KIFDEV to UMI
ERROR: %s: Timeout at page %#0x
DEBUG addr %#0x
ERROR: %s: Timeout at page %#0x
DEBUG addr %#0x
DEBUG Invalid IOCTL %#08x, cmd
%s: unable to register device, dev-
DEBUG >name
DEBUG ath_pci: 32-bit DMA not available
ath_pci: cannot reserve PCI memory
DEBUG region
ath_pci: cannot remap PCI memory
DEBUG region) ;
DEBUG ath_pci: no memory for device state
%s: unable to register device, dev-
DEBUG >name
ath_dev_probe: no memory for device
DEBUG state
%s: no memory for device state,
DEBUG __func__
DEBUG kernel MIBCTL registration failed!
DEBUG Bad ioctl command
DEBUG WpsMod: Failed to configure gpio pin
WpsMod: Failed to register interrupt
DEBUG handler
DEBUG registering char device failed
DEBUG unregistering char device failed
%s:%d - ERROR: non-NULL node
DEBUG pointer in %p, %p<%s>!
%s:%d - ERROR: non-NULL node
DEBUG pointer in %p, %p<%s>!
DEBUG can't alloc name %s, name
%s: unable to register device, dev-
DEBUG >name
failed to automatically load module:
DEBUG %s; \
Unable to load needed module: %s; no
DEBUG support for \
DEBUG Module \%s\ is not known, buf
DEBUG Error loading module \%s\, buf
DEBUG Module \%s\ failed to initialize, buf
262
User Manual
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR