Page 1
. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353.
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. SKU 92658 For technical questions, please call 1-800-444-3353. PRODUCT SPECIFICATIONS 1 Hp, 120 Volts, 60 Hz, 5.5 Amps (no load)
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. SKU 92658 For technical questions, please call 1-800-444-3353. ELECTRICAL SAFETY...
Page 4
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. SKU 92658 For technical questions, please call 1-800-444-3353. TOOL USE AND CARE Page 4...
Avoid unintentional starting. Make sure you are prepared to begin work before turning on the Tile Saw Do not force the Tile Saw. This tool will do the work better and safer at the speed and capacity for which it was designed.
Page 6
Blade. Use an appropriate “push stick” (not included) when necessary. Check Blade Guard for proper forward/backward movement before each use. Do not operate the Tile Saw if the Blade Guard does not move freely. Make sure the Blade Guard moves freely and does not touch the Saw Blade or any other part of the Saw, in all angles and depths of cut.
Page 7
Never run the Tile Saw without a water supply. Running the unit without a water supply will cause irreparable damage to the Pump. Make sure the water supply used for the Tile Saw is not dirty, sandy, and does not contain any corrosive chemical products.
Page 8
Do not force the workpiece into the Saw Blade when cutting. Apply moder- ate pressure, allowing the Saw Blade to cut without being forced. Turn off the Tile Saw and allow the Saw Blade to stop on its own if the Saw Blade is to be backed out of an uncompleted cut.
Page 9
Always turn off the Tile Saw and unplug it from its electrical outlet before changing accessories or performing any inspection, maintenance, or cleaning procedures. WARNING! The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied the operator.
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE A SKU 92658 For technical questions, please call 1-800-444-3353. GROUNDING WARNING!
‘W-A’ (‘W’ in Canada) to indicate they are acceptable for outdoor use. Always disconnect the extension cord from the receptacle before disconnecting the tile saw from the extension cord. Make sure your extension cord is properly wired and in good electrical condition.
Page 12
3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 16.0 16.1 - 20.0 FIGURE C SKU 92658 For technical questions, please call 1-800-444-3353. (120 VOLT) EXTENSION CORD LENGTH 50 FEET 75 FEET *Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
Page 13
When unpacking, check to make sure all the parts shown on the Parts List on page 18 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
Page 14
Check that both the Drain and the Additional Safety Overflow Drain are unclogged prior to operation. See FIGURE 4 below. Swing back the support Arm and adjust the Bevel Table (3) to its down position. SKU 92658 For technical questions, please call 1-800-444-3353. FIGURE 3...
Page 15
ASSEMBLY AND OPERATING INSTRUCTIONS (continued) Loosen the Locking Knob (16) on the Fence (13) which will disengage the Front and Rear Brackets (11 & 17). Place the Fence (13) on the Tile Saw as shown in FIGURE 5 below. Tighten the Locking Knob (16).
If that happens, immediately turn off the saw and wait until the unit is completely cool before starting it back up. When you are finished cutting, turn off the Tile Saw and unplug it from the outlet. Bevel Cutting...
16. INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Power Switch (24) of the Tile Saw is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 92658 For technical questions, please call 1-800-444-3353. PARTS LIST Qty.
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 92658 For technical questions, please call 1-800-444-3353. Page 19...