Changing The Delay Time (Speaker Settings) - Panasonic SC-HT535 Operating Instructions Manual

Video Out (AV/Component)
Choose the video signal format to be
output from the SCART (AV) and
Component terminal.
Still Mode
Specify the type of picture shown
when paused.
NTSC Disc Output
Choose PAL 60 or NTSC output when
playing NTSC discs (➜ page 11,
Video systems)
Picture/Video Output
Change the video signal format to be
output for JPEG, MPEG4 and DivX
video if picture output is not smooth
during playback.
∫ " Audio " tab
Dynamic Range Compression
Speaker Settings (➜ below)
Set the delay time for your center and
surround speakers.
∫ " Display " tab
Menu Language
On-Screen Messages
Background during Play
Select background during JPEG,
MPEG4 and DivX video playback.
∫ " Others " tab
FL Dimmer
Changes the brightness of the unit's
display.
DivX Registration
Displays the unit's registration code.
QUICK SETUP
Re-initialise Setting
This returns all values in the Setup
menus to the default settings.

Changing the delay time (Speaker Settings)

(Effective when playing multi-channel audio)
(Center and surround speakers only)
For optimum listening with 5.1-channel sound, all the speakers,
except for the subwoofer, should be the same distance from the
seating position. If you have to place the center or surround
speakers closer to the seating position, adjust the delay time to
make up for the difference.
C
: Actual speakers position
L C R
: Ideal speakers position
a
c
a b c
SW
b
LS
RS
Approximate room dimensions
LS
RS
Circle of constant primary listening distance
If either distance a or b is less than c, find the difference in the
table and change to the recommended setting.
a Center speaker
Difference (Approx.) Setting
30 cm 1.0 ms
60 cm 2.0 ms
90 cm 3.0 ms
120 cm 4.0 ms
150 cm 5.0 ms
≥Video/YPbPr
≥RGB/No Output
≥Automatic
≥Field:
The picture is not blurred, but picture quality is lower.
≥Frame: Overall quality is high, but the picture may appear blurred.
≥PAL60: When connected to a PAL television.
≥NTSC: When connected to an NTSC television.
≥Automatic ≥PAL
≥NTSC/PAL60: Output will depend on "NTSC Disc Output" setting (➜ above).
≥Off
≥On: Adjusts for clarity even when the volume is low by compressing the range of the lowest sound
level and the highest sound level. Convenient for late night viewing. (Only works with Dolby
Digital)
≥Center:
0.0/1.0/2.0/3.0/4.0/5.0 ms
≥Surround (L/R):
0.0/5.0/10.0/15.0 ms
≥English ≥ Français ≥Deutsch ≥Italiano ≥Español ≥Polski ≥Svenska ≥Nederlands
≥On ≥Off
≥Black ≥Grey
≥Bright ≥Dim
≥Auto: The display is dimmed, but brightens when you perform some operations.
You need this registration code to purchase and play DivX Video-on-Demand (VOD) content.
(➜ page 30, About DivX VOD content)
≥Yes ≥No
≥Yes: The password screen is shown if "Ratings" (➜ page 20) is set. Please enter the same password.
After "INIT" on the display disappears, turn the unit off and on again.
≥No
: Primary listening distance
b Surround speaker
Difference (Approx.) Setting
150 cm 5.0 ms
300 cm 10.0 ms
450 cm 15.0 ms
≥S-Video/YPbPr
1 Press [3, 4] to select the delay time box and press
[ENTER].
2 Press [3, 4] to adjust the delay time and press [ENTER].
To finish the speaker setting
Press [2] to select "Exit" and press [ENTER].
When you change the surround speaker setting for Dolby Digital, the
setting also changes for Dolby Pro Logic II.
e.g., the settings for MUSIC are the same as those for Dolby Digital.
Dolby Digital
0 ms
5 ms
10 ms
15 ms
Center delay time
L R
ms C
0.0
Exit
Exit
SW
ms
LS RS
0.0
Surround delay time
Dolby Pro Logic II
MUSIC MOVIE
0 ms 10 ms
5 ms 15 ms
10 ms 20 ms
15 ms 25 ms
RQT8225
21