Changing The Remote Control Code; Changing The Delay Time (Speaker) - Panasonic SC-HT1000 Operating Instructions Manual

Changing the unit's settings
Numbered
buttons
3, 4, 2, 1
ENTER

Changing the remote control code

Panasonic DVD players and recorders use the same remote control
system so they may respond unintentionally to a command from this
remote control. Change the code on this unit and its remote control
(the two must match) if you place equipment close together.
≥Use "1", the factory set code, under normal circumstances.
While SETUP menu screen is displayed
1
Press [3, 4] to select "Set Up" and
press [1].
2
Press [3, 4] to select "Remote
Control Code" and press [ENTER].
3
Press [3, 4] to select the code (1, 2,
or 3) and press [ENTER].
The remote control code on the unit has been set.
4
While pressing [ENTER] on the remote
control, press and hold for about 2
seconds the numbered button ([1], [2]
or [3]) corresponding to the code you
selected in step 3.
The remote control code on the remote control has been set.
The following display appears when you use a remote control with a
different code.
The unit's remote control code
Change its code to match the unit's (➡step 4).
RQT7061
42
HOME THEATER TV
POWER POWER
VCR Plus+
DVD FM/AM
DISPLAY OPEN/CLOSE INPUT SELECT TV/VIDEO
1 2 3
CH
4 5 6
VOLUME
7 8 9
CANCEL
0 100
SKIP SLOW/SEARCH
STOP PAUSE PLAY/x1.3
DIRECT NAVIGATOR PLAY LIST
TOP MENU MENU
ENTER
CH SELECT
FUNCTIONS RETURN
RETURN
MIX
L1/OPT 2CH TEST PRO LOGIC
FRAME CM SKIP TIME SLIP
PROG/CHECK ADD/DLT ERASE REC
MULTI REAR S.POSITION C.FOCUS
STATUS MARKER F.Rec REC MODE
P.MEMORY AUDIO SETUP
SHIFT SHIFT
EQ/SFC S W. LEVEL MUTING

Changing the delay time (Speaker)

Enhance sound perception using this feature. Adjust the delay time
for Dolby Digital when receiving multi-channel digital audio
broadcast on satellite or cable TV, or for Dolby Pro Logic II when
Dolby Pro Logic II is turned on.
While SETUP menu screen is displayed
1
Press [3, 4] to select "Audio" and
press [1].
2
Press [3, 4] to select "Speaker" and
press [ENTER].
Center delay time
Multi Channel
L
ms C
0.0
Complete
SELECT
ms
LS
ENTER
5.0
RETURN
Surround delay time
3
Press [3, 4] to select the delay time
box and press [ENTER].
4
Press [3, 4] to adjust the delay time
and press [ENTER].
L R
C
a
SW
c
b
LS RS
Values
If distance a or b is greater than or equal to distance c, set to "0".
If distance a or b is less than distance c, set as follows.
a Center speaker
Difference
Approx. 30 cm (1 foot)
Approx. 60 cm (2 feet)
Approx. 90 cm (3 feet)
Approx. 120 cm (4 feet)
Approx. 150 cm (5 feet)
b Surround speakers
Difference
Approx. 150 cm (5 feet)
Approx. 300 cm (10 feet)
Approx. 450 cm (15 feet)
When you change the surround speaker setting for Dolby Digital, the
setting also changes for Dolby Pro Logic II.
When you are finished
Press [2] to select "Complete" and press [ENTER].
R
SW
RS
Setting
1.0 ms
2.0 ms
3.0 ms
4.0 ms
5.0 ms
Setting
5.0 ms
10.0 ms
15.0 ms