Panasonic SC-XH50 Operating Instructions Manual page 19

Video Resolution
This works only when the HDMI connection is being
used.
Select suitable picture quality with your TV.
(Video recordings will be converted to, and output as,
high-definition video.)
≥[Auto] ≥480i/576i
≥1080i ≥1080p
Ensure that your TV can support the resolution that you
choose.
If a message screen appears, confirm your selection by
pressing [2, 1]8 to select "Yes" and press [OK]8. If the
picture is distorted, wait for 15 seconds or press
[2, 1]8 to select "No". To accept the setting, select
"Yes" again.
HD JPEG Mode [JPEG]
(This works only when using HDMI connection with
"Video Resolution" ( above) set to "Auto", "720p",
"1080i" or "1080p".)
≥[On]: HD JPEG playback is available. (JPEG images
will be displayed in original resolution.)
≥Off
During HD JPEG playback, there will be no on-screen
menus ( 15) and on-screen displays.
Video Out-SCART
Choose the video signal format to be output from the
SCART (AV) terminal.
≥Video
≥S-Video
≥RGB 1: (Only when connected to a RGB compatible TV)
If you always would like to view the picture from the unit
in RGB signal, select this mode. The TV screen will
automatically switch to display the picture from the unit
when the unit is turned on.
≥[RGB\2]: (Only when connected to a RGB compatible TV)
When in TV tuner mode, if the selector is set to "DVD/
CD", the TV screen will automatically switch to display
the picture from the unit only during disc playback
([DVD-V] [VCD]) or when viewing on-screen menu of
DVD/CD.
The TV picture will be displayed when the selector is set
to "AV". With other selectors, the picture from this unit will
be displayed.
Audio menu
Select to suit the type of equipment you connected to the
HDMI AV OUT terminal.
Select "Bitstream" when the equipment can decode the
bitstream (digital form of 5.1-channel data). Otherwise,
select "PCM".
(If the bitstream is output to the equipment without a
decoder, high levels of noise can be output and may
damage your speakers and hearing.)
Digital Output
≥Bitstream ≥[PCM]
When audio output is from HDMI AV OUT terminal, and
the connected equipment does not support the item
selected, the actual output will depend on the
performance of this connected equipment.
≥480p/576p ≥720p
Dynamic Range
≥On: Adjusts for clarity even when the volume is low.
Convenient for late night viewing. (Only works
with Dolby Digital)
≥[Off]
Speaker Settings
Select the delay time of the speakers.
(Effective only when "Surround layout (Recommended)"
mode is selected in "Speaker layout" (
(Center and surround speakers only)
For optimum listening with 5.1-channel sound, all the
speakers, except for the subwoofer, should be the same
distance from the seating position.
If you have to place the center or surround speakers
closer to the seating position, adjust the delay time to
make up for the difference.
:
C
L C R
:
SW
LS Approximate room
RS
dimensions
LS RS
Circle of constant primary listening distance
If either distance a or b is less than c, find the
difference in the table and change to the recommended
setting.
a Center speaker
Difference
Setting
(Approx.)
30 cm 1ms
60 cm 2ms
90 cm 3ms
120 cm 4ms
150 cm 5ms
≥C Delay (Center Delay):
[0ms]
, 1ms, 2ms, 3ms, 4ms, 5ms
Select the delay time for your center speaker.
≥LS/RS Delay (Left Surround/Right Surround Delay):
[0ms]
, 5ms, 10ms, 15ms
Select the delay time for your surround speakers.
≥Test Tone:
Use the test tone to listen to the speaker output to
confirm speaker connections.
Test tone will be output to each channel in the following
order.
Left, Center, Right, Surround Right, Surround Left,
Subwoofer
To stop the test tone, press [RETURN]D.
9, Easy setup).)
Actual speaker position
Ideal speaker position
Primary listening
:
distance
b Surround speaker
Difference
Setting
(Approx.)
150 cm
300 cm
450 cm
5ms
10ms
15ms
19