Advertisement
Electrical connection
If your house has aluminum wiring, see
"Ebctrical requirernents", Page 2.
Electrbal Shock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Electrically ground range.
Failure to follow these instructions can result
in death, fire, or electrical shock.
This oven is manufactured
with white
{neutraJ)
power supply wire and a cabinet=connected
bare
grounding
wire twisted
together.
Feed oven cane through opening in
the cabinet. Make electrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
U.L.-listed conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
6. Complete electrical connection according to
local codes and ordinances.
cable from
junction
power
supply
box _
re.,_
white _
-:_
w,re _
_>_
grounding
oven
cable wires
--
factory
crimped
Figure 1
cable from
oven
conduit
connector
ff local codes PERMIT
connecting
cabinet-grounding
conductor
to neutral white
wire in junction
box:
7. Connect the factory-crimped
bare and white oven cable wires
to the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
cabb from
iunction
power supply
Figure 2
cabte from
connector
oven
If local codes DO NOT PERMIT
connecting
cabinet-grounding
conductor
to neutral white
wire in junction
box:
7. Separate the factory-crimped
bare and white oven cable wires.
8. Connect white oven cable wire to
neutral (white) wire in junction
box. See Figure 2.
9. Connect the bare grounding
oven cable wire to a grounded
wire in the junction box. See
Figure 2.
10. Replace junction box cover.
If connecting
to a
four-wire electrical system:
7. Separate bare and white oven
cable wires.
8. Connect white oven cable wire
to neutral (white) wire in
junction box. See Figure 2.
9. Connect the bare grounding
oven cable wire to the green
grounding wire in junction box.
Do Not connect bare grounding
wire to neutral {white} wire in
junction box. See Figure 2.
10. Replace junction box cover.
Attachment
Carefully push against sea_area of oven front
frame when pushing oven into cabinet.
Do Not push against outside edges.
5[]
Lift oven into cabinet cutout using the
oven opening as an area to grip.
shipping
foot
Push against seal area of front frame to push
oven into cabinet until shipping feet almost
contact cabinet. Use a Phillips screwdriver to
remove screws attaching shipping feet. Remove
and discard shipping feet.
Push oven completely into cabinet and center
oven in cabinet cutout.
4 screws
6[]
Important: Securely fasten oven to cabinet
using the screws provided (two screws for a single
oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not
overtighten screws.
Slide top
of trim up.
Push trim
into place.
Repmace
trim screw.
/
7[]
Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.
8[]
Replace oven racks.
Important: Replace the door with the model/serial
rating plate on the upper oven.
On some models, the construction of this door is
designed to withstand self-cleaning temperatures.
9[]
Reinstall the oven door by inserting ends
of hinges into hinge slots in the oven frame. Push
hinges in as far as they will go, Open the door
(you will feel the door drop into place) and rotate
both binge tatches back to the locked position.
Close and open the door to check that the door
closes and opens completely,
if door does not
dose or open completely,
repeat the door
removal
step and reinstall
door as described
above,
Repeat for lower oven door.
Check operation
[] Turn on power supply. The display
panel will light up briefly. "PF" should appear in
the temperature display.
the display. Press the "START" pad. Make sure the
oven door is closed and the "ON" light is shown in
the display area. After 2 minutes, partially open
oven door. You should feel heat from the oven.
Press the "CANCEL" pad.
Check the operation of your double oven.
Press the "Upper Oven" pad. Press the "BROIL"
pad. "BROIL" will appear in the display. Press the
"START" pad. Make sure the oven door is closed
and the "ON" light is shown in the display area.
After 2 minutes, partially open oven door. You
should feel heat from the oven. Press the
"CANCEL" pad.
Press the "Lower Oven" pad and repeat the steps
you completed for checking the upper oven.
If your oven does not heat or an "F", foibwed
by a number,
appears in the display,
contact
your dea_er or check the "ff you need service..."
section
of this Installation
_nstructions.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep installation
hstructions
and Guide cmoseto oven
for easy reference.
Page 3
Advertisement
