Classic Series Custom Panels - KitchenAid KSSS42QTX04 Installation Instructions Manual

If you plan to install custom wood panels, you will need to create
the panels yourself or consult a qualified cabinetmaker or
carpenter. See dimension drawings for panel specifications.
IMPORTANT: Panels weighing more than recommended may
cause damage to your refrigerator.
NOTE: Dimensions shown have a (+)Vlo" (1.5 mm) tolerance.
Panels that are more than V4" (6.35 mm) thick must be routed. If
panels are less than V4"(6.35 mm) thick, install a filler panel
between the doors and decorative panels.
Top Grille Panel
The top grille panel should not weigh more than 10 Ibs (4.5 kg).
NOTE: The dashed lines in the illustration represent the location
and offsets of raised wood panel.
7" i
(17.78 cm) _ e Offsets
v. "I 7/16"(1.11 cm)
Top & Bottom Offsetsj
1/4"thick 11/16" (1.75 cm)
plywood
Model A
36 34V4" (87.0 cm)
42 40V4" (102.2 cm)
48 46V4" (117.5 cm)
Door Panels for Non-dispenser Models
The freezer panel should not weigh more than 40 Ibs (18.1 kg).
The refrigerator panel should not weigh more than 50 Ibs (23 kg).
_t_
7-
1,/2,,
(1.27 cm)
r ..... I
I
I
I
I
Freezer
Door
Non-Dispenser)
3,/_%,J
(8.3 cm) ,
I
I
I
I
t'
1/2,,
(1.27 cm)
[.,_-- B ---------------_
Refrigerator
Door
Location and offsets
of raised wood panel
_t
7-
1/2,,
(1.27 cm)
7//16"
(1.1 cm)
W' thick
plywood
_t
7-
1/2,,
(1.27 cm)
Model A B
36 141/4"(36.2 cm) 191/4"(48.9 cm)
42 163/4 '' (42.6 cm) 223/4" (57.8 cm)
48 19V4" (48.9 cm) 26V4" (66.7 cm)
NOTES:
• If the standard handle is used, the handle side offset of
both panels should be 3V4" (8.25 cm) to all for finger
clearance.
If an extended handle is used, the handle side offset of
both panels should be 7/lo" (1.1 cm). Make sure the
refrigerator location allows the doors with extended
handles to open to 90 degrees. See "Door Swing
Dimensions."
The dashed lines in the illustration represent the location
and offsets of raised wood panel.
Door Panels for Dispenser Models
The freezer panel should not weigh more than 40 Ibs (18.1 kg).
The refrigerator panel should not weigh more than 50 Ibs (23 kg).
_t _-_ A-_
7-
1/2,,
(1.27 cm)
141/4"
(36.2 cm)
333/4"
(85.7 cm)
I-- .....
I
I
I
I
I
Freezer
Door
(Dispenser)
I
I
I
-----.
Dispenser
cutout is
centered
left-to-right
I
I
31/4'_m,4
(8.3 cm)
,
I
I
I
.... t
_--B_
r
Refrigerator
Door
I
i_-- 31/4"
, (8.3 cm)
1/2,,
(1.27 cm)
Model A B
36 141/4"(36.2 cm) 191/4"(48.9 cm)
42 163/4"(42.6 cm) 223/4" (57.8 cm)
48 19V4" (48.9 cm) 26V4" (66.7 cm)
±
7-
1/2,,
(1.27 cm)
7_6"
(1.1 cm)
........ V4" thick
plywood
7-
Location and offsets W'
of raised wood panel (1.27cm)
NOTES:
• Dispenser cutout is centered left-to-right.
• If the standard handle is used, the handle side offset of
both panels should be 3V4" (8.25 cm) to all for finger
clearance.
If an extended handle is used, the handle side offset of
both panels should be 7/lo" (1.1 cm). Make sure the
refrigerator location allows the doors with extended
handles to open to 90 degrees. See "Door Swing
Dimensions."
The dashed lines in the illustration represent the location
and offsets of raised wood panel.
16